Tootle Puffers, Part Three! (The Sequel of the Redux)

[sorrynomore]

For someone who's only vaped an eGo aio since the hardware switch (my last unit before the Analog relapse was a silver bullet with vision tanks - BEFORE they were ANY sort of rebuildable)

Anyone fancy explaining the settings to me? (If it's too off topic just pm me I'm just a combination of super excited and ACUTELY aware that my SOLE aio left is on borrowed time and i need to get the eVic before that)

Hope everyone had a good day!!

I've owned an eVic VTwo mini for a few weeks now and I DO like it very much.I've only used it in wattage mode so I can't say much about the other settings.

Welcome to the thread & nice to see another Canadian as well!!!

Edited: I've had the eVic for a few months not weeks as written above.I don't know where my head's at sometimes grrrrr....

 

[Two_Bears]

13 more days till my big move to 4 corners area.

 

[Muru]

Sure hope you'll have a better internet connection there!

 

[Shawn Hoefer]

Yeah, I really hate a bad internet connection...

.......

ETA: yeah, it was an acronym. Yeah, it was censored. Nah, don't feel bad about it at all...

Sent from my SAMSUNG-SM-N910A using Tapatalk

 

[Bea-FL]

.......

ETA: yeah, it was an acronym. Yeah, it was censored. Nah, don't feel bad about it at all...

Sent from my SAMSUNG-SM-N910A using Tapatalk

And I thought mine was bad

 

[brewbear]

I tried super glue but it didn't hold.

My eVIC mini had the same problem. I used JB Weld, the 2 part epoxy. That magnet stays put , even though the mod has been dropped several times since.

 

[Eskie]

@kad2371 I just looked at the specs on the Merlin mini and found a deal breaker..it's 24mm so it won't fit on the Pico and if I put it on either the SX mini, the Clouper mini or the eVic mini the overhang would drive my OCD up the wall! You know me...I can't deal with overhang and my tanks can't be taller than the mod its sitting on. Off to look for something else. I need one more good RTA.

There are other options to the Merlin mini. A full size Merlin fits, as does a Serpent mini (the 22 mm version), Goblin mini v3, the Engine mini (almost positive on that, the measurements say it should), and a Bellus. So a bunch of different choices with varying volume.

 

[LynnNC]

My eVIC mini had the same problem. I used JB Weld, the 2 part epoxy. That magnet stays put , even though the mod has been dropped several times since.

Thank you!!

 

[markfm]

The good old tfv4 mini is a 22. The geekvape Ammit is also a 22. Aromamizer v2 is, iirc, a 23.

 

[LynnNC]

There are other options to the Merlin mini. A full size Merlin fits, as does a Serpent mini (the 22 mm version), Goblin mini v3, the Engine mini (almost positive on that, the measurements say it should), and a Bellus. So a bunch of different choices with varying volume.

Thanks Eskie! I think I've decided on the Engine mini. I already have the Merlin and the Serpent which are both in my rotation. I wanted the Merlin mini cause I love my full size Merlin so much. I'm also looking at another AugVapeRTA as well but can't remember the name at the moment.

 

[LynnNC]

The good old tfv4 mini is a 22. The geekvape Ammit is also a 22. Aromamizer v2 is, iirc, a 23.

Thanks Mark! Maybe I need to revisit the tfv4 before I buy something else.

 

[markfm]

The -r1 head for the tfv4 is a nice single coil head. I've got 3 or 4 floating around if you'd like one.

 

[brewbear]

Thank you!!

Just be careful with that stuff, it really sticks to everything. It is a cold weld so it takes a little while to set. Make sure the magnets are in the correct orientation, not the way I did it at first and the stupid door was popping out because the magnets were repelling each other. Use a marker or something on one of the faces.

 

[ames001]

lol, i'm fully aware of the other 2 threads O lol... if i catch up on this thread by friday i'll go back over the weekend

lol i'm currently without a car - and without a car i'm immobile so.... LOTS of free time till i find a car

 

[LynnNC]

The -r1 head for the tfv4 is a nice single coil head. I've got 3 or 4 floating around if you'd like one.

Is that the rebuilable coil head? I don't think I have one for the tfv4. I need to look. Thanks!

 

[brewbear]

Thanks Eskie! I think I've decided on the Engine mini. I already have the Merlin and the Serpent which are both in my rotation. I wanted the Merlin mini cause I love my full size Merlin so much. I'm also looking at another AugVapeRTA as well but can't remember the name at the moment.

I really like the Alleria from them, I have 4, two in continuous use, the other two are backups.

 

[LynnNC]

Just be careful with that stuff, it really sticks to everything. It is a cold weld so it takes a little while to set. Make sure the magnets are in the correct orientation, not the way I did it at first and the stupid door was popping out because the magnets were repelling each other. Use a marker or something on one of the faces.

I've done that when I've put that magnet back in the little slot.

 

[LynnNC]

I really like the Alleria from them, I have 4, two in continuous use, the other two are backups.

Thanks! I'll check out the Alleria. It's 22mm?

 

[Sir Kadly]

Goblin mini v3

Dangnabbit, I forgot that was on my wishlist. Am I allowed to buy myself a second birthday vape present?

 

[LynnNC]

Dangnabbit, I forgot that was on my wishlist. Am I allowed to buy myself a second birthday vape present?

You can buy yourself as many birthday presents as you want! My birthday is not just 1 day but the whole month. Of course I don't buy myself presents for the whole month but I do buy more than just 1 present!