Use your old parts for a cart mod 901

[Carlos49]

I have had this for a while testing it and it seems to work rather well. What I did was take a 901 battery case (empty), that I had from a dead bat, two empty carts. your also going to need one of those flat, two hole, coffee string straws. Cut one cart just below the divider of the mouthpeice and the filler chamber so you have a peice you can see through. When you cut that you should still have the section that is for air intake also. Slide the straw into the the air intake of the whole cart, use a little bit of glue to seal it in place. I used clear two part epoxy and just use a very tiny bit. Then slide the unit into the battery case, it's a nice fit. the other end you have to grind a shoulder onto it so it will fit into the battery housing, about 1/4 down. I used my Dremmel tool but you could also use a file. Once that's done push your straw into the air intake until you can push it into the bat housing. Once you have that done cut off the excess straw and seal with epoxy. The only thing that's left is to fill with your perferd filler material, I use Fluval Which is inserted through the bottom. Now this mod is long but you can cut down the Battery tube to whatever lenth you feel comfortable with.
I working on something similar for the penstyles and hope to have something soon.
Thanks for looking
Carlos


http://i638.photobucket.com/albums/uu107/caguiar_2009/PICT0156.jpg

 

[framitz]

I have had this for a while testing it and it seems to work rather well. What I did was take a 901 battery case (empty), that I had from a dead bat, two empty carts. your also going to need one of those flat, two hole, coffee string straws. Cut one cart just below the divider of the mouthpeice and the filler chamber so you have a peice you can see through. When you cut that you should still have the section that is for air intake also. Slide the straw into the the air intake of the whole cart, use a little bit of glue to seal it in place. I used clear two part epoxy and just use a very tiny bit. Then slide the unit into the battery case, it's a nice fit. the other end you have to grind a shoulder onto it so it will fit into the battery housing, about 1/4 down. I used my Dremmel tool but you could also use a file. Once that's done push your straw into the air intake until you can push it into the bat housing. Once you have that done cut off the excess straw and seal with epoxy. The only thing that's left is to fill with your perferd filler material, I use Fluval Which is inserted through the bottom. Now this Mod is long but you can cut down the Battery tube to whatever lenth you feel comfortable with.
I working on something similar for the penstyles and hope to have something soon.
Thanks for looking
Carlos


http://i638.photobucket.com/albums/uu107/caguiar_2009/PICT0156.jpg

Good one Carlos.

I've done something similar for the penstyle:
http://www.e-cigarette-forum.com/forum/cartridge-mods/27002-pen-style-cart-capacity-mod.html
It works fairly good, but 3ml in the cart last almost too long, I need to cut it to two carts to make it easier to stuff and fill.

 

[Carlos49]

Good one Carlos.

I've done something similar for the penstyle:
http://www.e-cigarette-forum.com/forum/cartridge-mods/27002-pen-style-cart-capacity-mod.html
It works fairly good, but 3ml in the cart last almost too long, I need to cut it to two carts to make it easier to stuff and fill.

That's a good one Framitz I like that a lot... Don't know how I missed that one..LOL
Going to work on that when I get home...Thanks

 

[Twyztyd]

An atty tube is just about the right length. might still be a bit much for some but .
A complete one on the mouth piece and the air hole in the atty is covered up.Do everything else just the same as Carlos49 said and will work great.
No camera or I'd post a picor twh wait .... I dont even have enough posts for that I dont think.

 

[Craig Patterson]

Awesome...

Craig