2ML PLUS CART MOD woot woot

[Lightgeoduck]

Ok I had seen this concept awhile back from my man Carlos here on ECF... similarities but slight differences.... Soo I am not saying I invented or dreamed up a "new" idea,but I did figure it out on my own if you know what I am trying to say.

here is the vid and instructions below

YouTube - 2ml+cart.wmv

1 306 atty (this is the model you use for your atty)
1 dummy 306 mouth piece closed end cut off
1 kr808 PT... could use a kr808 batt or 901 bat(i find the pt easier)
1 rubber ring from kr808 cart
1 roll of filler from kr808 cart (can use any filler type i.e. blue foam or what ever)
1 small juice/stiring non flex straw
1 801 dummy tip

gut PT take center post out from battery connection

insert straw put rubber ring around straw and push deep into kr808 tube

fill approx 2ml liquid (could try more,, but I was satisfied with this)

wrap filler around end of straw push straw and filler flush to tube
top off with liquid

insert mod 306 mouth piece into tube opening leaving enough room to slide on atty

cut excess straw from connector end put 801 dummy piece over battery connector

finished

Thank you and enjoy

 

[the86d]

I would DIE, QUICKLY!

Maybe I could hit that like I normally do, if not more providing that I cut my nic down to maybe like .25mg/ml.

 

[Lightgeoduck]

I would DIE, QUICKLY!

Maybe I could hit that like I normally do, if not more providing that I cut my nic down to maybe like .25mg/ml.

hehe... well It was only a demo to show its performance... if you vape it normally i would imagine it would be nice and smooth. I know a normal cart can't handle that abuse... especially @ 6v hehe

 

[reeds101]

I had to keep watching to see if you were going to pass out. It looks like a great mod for around the house, but I don't think I'd want to carry it around with me. Fine job!

 

[Lightgeoduck]

I had to keep watching to see if you were going to pass out. It looks like a great mod for around the house, but I don't think I'd want to carry it around with me. Fine job!

hehe ... well its late at night for me as you can see my clock... thats pm so I always look like I am going to pass out

as far as the size thats a full length tube you could cut down the size... even half the size is better than a regular cart.... it last pretty long.... I would imagine if something other than regular filler will prolong the life of it.....

but I am fine with replacing the filler now and then.

 

[RatRacer]

It looks like a great mod for around the house, but I don't think I'd want to carry it around with me. Fine job!

I second that. I'd hate being stopped every 5 minutes asking where they could pick up a bottle rocket too.

Sit down and use a seat belt with this one.

 

[Lightgeoduck]

yeah it might be a little on the long side... but on a PT for home or in the car use... I would imagine it to be the WHATS WHAT of 2010 hehe

This thing is holding strong.... and is quite impressive if I do say so myself, (beep beep)

I just have to wait and refill this monster with some of my favorite liquid... i used some old marl bro mentho mix which is at the bottom of my list (for testing didn't want to chance wasting good stock)

IMM its worth a try

 

[Madame Psychosis]

Since I'm just enough of a foolhardy type to try this contraption... a few photos would be highly appreciated. Some of the steps were a bit unclear.

 

[Lightgeoduck]

Hopefully this makes it a little clearer

pic 1 parts blow up (801 mp, pt tube w/straw,rubber ring,mod 306 dummy)
pic 2 rubber ring from cartomizer stick over straw and push down the tube
filler is wrapped around straw and pushed in tube as a plug
pic 3 left 306 dummy right a 306 dummy cut

pic 4 battery connector end to show straw and 801 mouthpiece

don't hesitate to ask questions

 

[Theaxiom]

I like your shirt.