Vaporflask partnered with Wismec/Joyetech
- Thread starter Croak
- Start date
- th_trl_thread_readers 0
- Status
joyetech, wont touch anything made by/with them with a barge pole
I am a bit worrying because the black stout already chipped the paint on the edge on the picture...
And great they offer international shipping but only accept US credit cards from US residents. Makes sense, NOT.
And great they offer international shipping but only accept US credit cards from US residents. Makes sense, NOT.
I'll let ya folks know one way or the other. God only knows when they will actually ship.
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
Went to the VapeForward website and only black was listed as available. Im looking for a silver finish Stout. Does anyone know of another vendor to check? vaporbeast was also out of silver.
Silver satin is not available at this time. Black is the first to ship. You can confirm on the VF page on FB.
Mine is expected to arrive tomorrow. I'll report if it arrives.
Happy New Year.
Sent from my iPhone
Just did the un boxing and I have to say this mod looks and feels as good as any 200. plus dollar mod.
Never buy mods made in China but this a game changer for me.
I will own own the entire collection.
Job well done Vape forward.
Sent from my iPhone
So here is what I have so far.
Periodic lag when waking up from sleep mode. Fire button not very responsive. In temp mode when changing atty's after locking resistance the board should jump into "new coil up/ same down". This happened once and hasn't happened since.
I mean it worked once. Tested NI200 and I have to raise temp to 500 degrees to get a good vape. Fires 1.10 ohm kanthal in temp mode. Reads it at 1 ohm which is in range. I think the board reads ohms to the lower side by.05-.10 ohms. Also no presets (my personal dislike ).
Again I will say the design and craftsmanship of mod itself is fantastic. The battery door is even better.
I hope that I have a defective chip which can happen. I hope it can resolved quickly.
On the plus side in temp mode no burnt wick and I vaped it dry,dry,dry.
If someone has had better experiences it would great hear about it.
Sent from my iPhone
Periodic lag when waking up from sleep mode. Fire button not very responsive. In temp mode when changing atty's after locking resistance the board should jump into "new coil up/ same down". This happened once and hasn't happened since.
I mean it worked once. Tested NI200 and I have to raise temp to 500 degrees to get a good vape. Fires 1.10 ohm kanthal in temp mode. Reads it at 1 ohm which is in range. I think the board reads ohms to the lower side by.05-.10 ohms. Also no presets (my personal dislike ).
Again I will say the design and craftsmanship of mod itself is fantastic. The battery door is even better.
I hope that I have a defective chip which can happen. I hope it can resolved quickly.
On the plus side in temp mode no burnt wick and I vaped it dry,dry,dry.
If someone has had better experiences it would great hear about it.
Sent from my iPhone
Last edited:
@Jake67 that's surprising, considering it's the same basic, well-regarded, good-performing board as used in the RX200, Presa 75TC, eVic VTC Mini/Cuboid, etc.
Wow... That sounds like kinda a Hot Mess.
What level is your Firmware? I would be surprised that a New Mod like this Wouldn't come with the Latest Firmware. But stranger things have happened.
Firmware download can be downloaded at the Bottom of this page.
stout - Wismec Electronics Co.,Ltd
I don't dispute what your saying about the wide use of the same basic chip, I'm not that knowledgeable when it comes to the differences, however...During Charlie's introduction of the new lineup he said the chip was customized to his specs and my VTC Mini chip seems something very different than a Presa or RX200 chipset.
I'm a little surprised as well. Could just be a bad board.
That's what I'm hoping.
Sent from my iPhone
- Status
Similar threads
