What voltage do you vape at?

[Smithy963]

i vape a 2.8ohms head on 3.4v i find that my sweet spot for this flavor... But thats me and this e liquid... just experiment.. remember low ohms low volts higher the ohms more experimenting. and where abouts in brum you from?

Thanks everyone


I'm from Walsall/Tamworth depending upon how formally you're asking me

 

[Smithy963]

Geeez! The OP is using a Spinner. Don't confuse him with that stuff!

Lol!

I'm a programmer... I could blow you away with some of the math I do daily.

What's that star thing mean again though?

 

[Smithy963]

Some Reason Or Another I Always Find Myself Around 4.2-4.8, That's Just Where I Get The Best Flavor For Me.

Me too, I like the warmest hit I can get normally. I'll keep it bumped up until I get that burnt flavour knock it down a bit and then slowly start turning it up again.

 

[AttyPops]

Lol!

I'm a programmer... I could blow you away with some of the math I do daily.

What's that star thing mean again though?

"Star thing"? Disappointed. Not very specific for a programmer. I'd expect the Unicode sequence at least!

You mean this "*"? Depends.
Could mean "multiplication"
Or "Splat"
Or "asterisk"...see fine print.
Or...fireworks.

If by star thing...you mean something else......IDK.

 

[Smithy963]

"Star thing"? Disappointed. Not very specific for a programmer. I'd expect the Unicode sequence at least!

You mean this "*"? Depends.
Could mean "multiplication"
Or "Splat"
Or "asterisk"...see fine print.
Or...fireworks.

If by star thing...you mean something else......IDK.

I was alluring to (humorously and sarcastically) what you said in your second post.

Type of pv and mathematical intelligence have no correlation.

Do you want the standard asterisk (U+002A), the small asterisk (U+FE61) or a full width asterisk (U+FF0A)?

 

[AttyPops]

I was alluring to (humorously and sarcastically) what you said in your second post.

Type of pv and mathematical intelligence have no correlation.

Do you want the standard asterisk (U+002A), the small asterisk (U+FE61) or a full width asterisk (U+FF0A)?

OH! I get it!

LayOn Floor();
while (confirmPosteriorAttached()) {
Roll60Left();
Roll60Right();
Roll60Right();
Roll60Left();
}

 

[tj99959]

Some Reason Or Another I Always Find Myself Around 4.2-4.8, That's Just Where I Get The Best Flavor For Me.

That's only because you're in Turkey (jk)

I start out low, and bump it up to the optimum flavor, most of the time I find that to be a lot lower than you would think.
Right now I'm vaping Papa Berry juice with a 2.1 ohm coil in a RDA at 3.7v, however my Pama Berry juice starts to fry at 3.4v in that same RDA. Guess pomegranates just have a lower flash point.

 

[retired1]

OH! I get it!

LayOn Floor();
while (confirmPosteriorAttached()) {
Roll60Left();
Roll60Right();
Roll60Right();
Roll60Left();
}

You forgot your "do while laughing" statement.

 

[Smithy963]

You forgot your "do while laughing" statement.

That is his Rofl() function lol.

 

[hvac999]

I have my Vamo set on vw. This makes the Vamo adjust to the correct vv to accomplish my vw. When I used a Spinner I liked about 4.3v.

 

[Smithy963]

So for those who like a specific voltage/wattage its the same all around for different types and flavours?

From the watery juice to the treacle juice? The citrusy fruit flavours to the coffees and chocolates?

You find a power output and stick to it all around?

 

[retired1]

No. I find the more subtle flavors do better with a slightly lower voltage. Where the heavier flavors do well with a higher voltage. Again, it's all about dialing it in and finding your own optimal power output for the flavor you're vaping.

 

[AttyPops]

You forgot your "do while laughing" statement.

OH! I get it!

LayOn Floor();
while (confirmPosteriorAttached()) {
Roll60Left();
Roll60Right();
Laugh();
Roll60Right();
Roll60Left();
Laugh();
}

No. I find the more subtle flavors do better with a slightly lower voltage. Where the heavier flavors do well with a higher voltage. Again, it's all about dialing it in and finding your own optimal power output for the flavor you're vaping.

Like some fruit flavors burn easily. Lime. Burns easy. Different coils are....different...too. So yeah. That's why people adjust VW stuff. lol.

 

[Waldo919]

Whatever tastes best to you! Im using a LavaTube and a 2.5ohm ProTank at 4.2V All depends on flavors and personal preferance.

 

[smithy]

I use an eRoll, so 3.2v-4.2v. Then again I'm new to all this so I could be wrong.

 

[retired1]

I use an eRoll, so 3.2v-4.2v. Then again I'm new to all this so I could be wrong.

If it works for you, and it tastes good, you're doing it right. It's that simple.

 

[DaveP]

Function VoltageAdjust
.....Do
..........CrankVoltage(.1)
..........If CoilPop = True
...............ChangeHead
..........Endif
.....Until BurntTaste > Flavor
.....DecreaseVoltage(.1v)
End Function

ContinueVaping


(Dang CHR(20) remover algorithm ... took out my formatting)

 

[retired1]

I'd be even more impressed if you wrote that in COBOL.

 

[DaveP]

I'd be even more impressed if you wrote that in COBOL.

Had to do one COBOL Hello World program in my first CPSCI class in the 80's just because the professor wanted us to see how things used to be done! It took a page for just the initial setup and global declarations, then the single statement to display "Hello World".

 

[spegtoast]

With my Watermelon flavor I have been right around 4v. With the Honey cigar flavor I use it at the lowest setting 3.2v And I have to agree with you retired1. Besides.. No need to calculate. Just adjust to taste, and vape away.