An idea of the iatty
Wick was bought from here:
http://www.wickstore.com/Products/Round-Fiberglass-Wick-116-100-Yards__1376-100.aspx
no resistance wire was bought from here:
http://www.wires.co.uk/cgi-bin/sh00...6&PN=ni_bare.html#aNI0236_2d050#aNI0236_2d050 50g 0.236mm Nickel Wire
heating wire was bought from here:
http://www.wires.co.uk/acatalog/nc_bare.html 50g 0.16mm Nickel Chrome Wire
or if you want thinner wire you can buy 0,122mm ir 0,132mm
After too many experiments, the best vaping experience with Iatty is with a 1,5 ohm resistance to my opinion. The wick inside Iatty is fat so it can easily handle the liquid demand. And there is also the liquid control that can allow us to use different liquids (thin or fat) and to feed more or less the Iatty. You can still put a thinner wire (0.13 for example) to have more smoke or to be able to put bigger resistance (e.g. 2ohms)
For 6 volts I recommend 3ohm resistance
refillings methods if you have a burn taste:
open close the cap 4-5 times
open the liquid control more for a continous better taste or close it according to the needs of the liquid you use
dripping
Only on GGTS, close the CR and take 3-4 long inhales without pushing the button
I desided to send 2 different o-rings for the ceramic of the Iatty. You put the very small one first on ceramic and then the bigger one. I did this to make it easier to fit them inside ceramic.
If you overflood the Iatty just blow from its bottom and the liquid will come out of the mouthpiece. To avoid the overflooding push very good the wick inside slots of the upper plastic
put all the resistance inside the ceramic otherwise you may damage the plastic under the ceramic
Make very tight threads and close each other
buy 0,13mm wire for even better results
Wick was bought from here:
http://www.wickstore.com/Products/Round-Fiberglass-Wick-116-100-Yards__1376-100.aspx
no resistance wire was bought from here:
http://www.wires.co.uk/cgi-bin/sh00...6&PN=ni_bare.html#aNI0236_2d050#aNI0236_2d050 50g 0.236mm Nickel Wire
heating wire was bought from here:
http://www.wires.co.uk/acatalog/nc_bare.html 50g 0.16mm Nickel Chrome Wire
or if you want thinner wire you can buy 0,122mm ir 0,132mm
After too many experiments, the best vaping experience with Iatty is with a 1,5 ohm resistance to my opinion. The wick inside Iatty is fat so it can easily handle the liquid demand. And there is also the liquid control that can allow us to use different liquids (thin or fat) and to feed more or less the Iatty. You can still put a thinner wire (0.13 for example) to have more smoke or to be able to put bigger resistance (e.g. 2ohms)
For 6 volts I recommend 3ohm resistance
refillings methods if you have a burn taste:
open close the cap 4-5 times
open the liquid control more for a continous better taste or close it according to the needs of the liquid you use
dripping
Only on GGTS, close the CR and take 3-4 long inhales without pushing the button
I desided to send 2 different o-rings for the ceramic of the Iatty. You put the very small one first on ceramic and then the bigger one. I did this to make it easier to fit them inside ceramic.
If you overflood the Iatty just blow from its bottom and the liquid will come out of the mouthpiece. To avoid the overflooding push very good the wick inside slots of the upper plastic
put all the resistance inside the ceramic otherwise you may damage the plastic under the ceramic
Make very tight threads and close each other
buy 0,13mm wire for even better results
Last edited: