Attack of the (Kayfun Mini V3) Clones!
- Thread starter KTMRider
- Start date
- th_trl_thread_readers 0
- Status
I just use 1 turn on 70% VG. Absolutely no dry hits but I'm using rayon.
Enviado do meu GT-I9195 através de Tapatalk
Enviado do meu GT-I9195 através de Tapatalk
Guys, is the MAP code still working on fasttech? It gives me "invalid coupon"
I can't figure out where to enter that code!
Go to your 'cart' not checkout, bottom right will say 'have coupon?' click that and a box appears to enter the coupon code.
Anyone building micro coils in these? My preferred build for my KFL+s is a 28g, 11 wrap on 5/64" bit, 1.6 ohms at 3.7 volts. Will something like this work in this little tank, or am I going to have to get creative again?
Just FYI, the SKX I had ordered, and fasttech told me future batches would not have glass tanks, only plastic, so I cancelled my order for that version.
Most orders take 2-3 weeks on average.
I did them with 28g..8/7wraps one at 2.5 and one 3mm both spaced..I see how that goes..
On one I went to adjust the afc and it was full of juice under the 510 pin..no idea why..
On one I went to adjust the afc and it was full of juice under the 510 pin..no idea why..
I just pulled out 2.5mm 28g 1.5/1.6 ohm contact coil and it was working fine
As I mentioned in earlier post, I got Tobecos (1black, 1SS) from VapeNW and they aren't machined great but good enough to clean em good and check over good first qnd they vape great. As far as chain vaping or dry hits, I use ... cotton and 1.5ohm 27ga or 28ga and vape 100% VG with slow long drags......no dry hits once wicked properly! But I did modify both- found a drill bit just tiny bit bigger than those four juice holes under wick ends and bored them out. Easy with an experienced hand and good drill bit. They just looked too small for my seriously thick actual 100% VG. With 2 1/4 turns open I've been fine, actually really loving it most of the time. Just once in a while something doesnt taste or hit perfect and cant figure that out yet
Yup for sure, almost exactly what im using
And just checked now I'm at 1.45ohm set at 9.6watts which shows 3.73v on my cloupor mini. Vaping super delicious and satisfying right now, literally as good as any other setup I've used....ever.
Last edited:
Might be a bit too long. Try a 7/64 (2.5mm) coil with 8/9 wraps. As others have said, pretty much any coil works on this.
Thanks for the review of the Tobecos. Try adjusting the afc screw. Turn it all the way in and then out until you like the draw. If it's out too much, it screws with the resistance for some reason. Once I adjusted mine, it's been working flawlessly.
Yes. Got a v3 and tested a v4. With all it's limitations, as far as flavor goes, among RBAs, Spheroid v3 is unique. V4 is very good, but not the same in flavor department as v3, in my opinion.
Same here. I have a few v2s with the v3 upgrade - I never bought the v4 because I feel the v3 can not be improved upon. I have one dedicated to a tobacco vape that is divine in the evening. Like a fine cigar. I can not get that particular juice to taste as good or better in any other tank I own. I was looking for a good rich tobacco flavor for evening when I unwind and the Spheroid did not let me down. Excellent MTL vape that is warm and bold.
Does anyone know which version is the one sold on 3F Vape? I want to get the same version from FT.
Anyone got their hands on the "plus" version with 3.5ml tank? There are two of them at Fasttech: One for $13.61 with chrome center pin and one for $20.65 with SS pin. No reviews yet for either.
- Status
