chinese knockoff

[mgmrick]

hi i am waiting for my lavatube from hereStainless-Steel-VV-350 (3V To 6v) starter kit and what i would like to know is,it uses x2 18350 batteries,could i use x1 18650 battery.
it is just a thought.any advise will be much appreciated...thanks from the uk

I have been using this mod for a few months from a usa a vendor. I have used alot of vv china mods (including the vmax) you are going to love this mod. The best china mod I use hands down. Yes you need to use stacked batteries in it.

 

[terry w]

well guys here goes...i started off by filling 1 of the tanks that came with the kit,and they are rubbish they are a kind of transparent plastic carto filled with some sort of sponge,and after filling 1 and letting it sit for a while,fired it up at 3v, nothing,3.5,a little vapour 4.5,burning taste but a bit more vapour.I then decided to put a 2.8 ohm atty in my vivi,and started,again at 3v and bang,whallop,kick my ....,it was vaping like a champ.I am so pleased with it,although i think it may take a while to get used to.I suppose my next question would be, is this...Why make something what can put out 6v,when it works well at 3v.it may seem like a stupid question,but why would i need to go any higher than 3v,when i am getting a lovely tasting vape ? thanks for your help...Terry

 

[terry w]

you are dead correct rick,i love it

 

[mgmrick]

I have a bunch of china vv mods and this like I said hands down this is the best. The vmax has too high of a volt spike where this is not as high. I run dual coils 1.5 ohm at about 5 volts. Running my did clones with 1.8 ohm I run them at about 4 volts

Yeh the carto's included in the kit are junk just toss them... oh well the mod more than makes up for the junk carto's

Its being sold as the varitube-3 here in the states but the same model you have

 

[terry w]

apparently plumes according to the certitificate of authenticiy... s.........which came with the package,it is battery chip protected,and it does indeed have a vent hole on the bottom cap,but thanks for your concerns buddy

 

[terry w]

thanks rick,i thought i was doing something wrong at first,heading for the bin right now mate

 

[mgmrick]

It is indeed protected. It flashes on a coil below 1.5 ohms and vented bottom cap

apparently plumes according to the certitificate of authenticiy... s.........which came with the package,it is battery chip protected,and it does indeed have a vent hole on the bottom cap,but thanks for your concerns buddy

 

[BlueSnake]

Wow ok! dude thankyou,this is why i ask questions ? cos you can`t get that sort of info,from anywhere else.
you must remember that i am trying to do dealings with a chinese vendor.And the info i received is a little bit jibberish,if you know what i mean...it seems like i have been given the correct advice from the vendor... AND YOU I think what the vendor is trying to say is that,if i use a low resistance atty or carto...is to keep the volts to a minimum so as not to damage the unit,so i will do as muzichead says and just use the higher resistance stuff...cheers guys

I have one of these and it really is a nice pv. It is not meant for LR vaping. I use 2.5ohm and above with no problems. If you use Vivi Novas start low and work your way up slowly until you find a spot where you are satisfied with the taste and vapor. If something starts to taste burnt back it down.

It does only use 2 18350 batteries. And the top and bottom of the unit is press fit. If you drop it, it can come apart. Also there is no ohm reader on this PV. All in a nice PV for the money.

 

[BlueSnake]

thanks rick,i thought i was doing something wrong at first,heading for the bin right now mate

Don't believe Rick, he's never even seen one of these. lol

Just kidding.

 

[mgmrick]

In fact rick owns 2 of them...lol

 

[terry w]

so i have a question guys,i have some low resistance cartos for my dct,will they be ok to use or not.If i remember correctly they are 1.7 ohm,but not 100% sure ???

 

[mgmrick]

I run 1.5 ohm duals no problem and as low as 1.5 ohm on did clones

so i have a question guys,i have some low resistance cartos for my dct,will they be ok to use or not.If i remember correctly they are 1.7 ohm,but not 100% sure ???

 

[terry w]

thanks rick, the reason i ask is; if you read the warning at the bottom of the page,you will understand my concerns.After all this is my new baby,so being extra carefull not to harm her...LOLcheapest, stainless steel, vv-350 ecig on the internet, and by the way mate what is a did ?

 

[mgmrick]

thanks rick, the reason i ask is; if you read the warning at the bottom of the page,you will understand my concerns.After all this is my new baby,so being extra carefull not to harm her...LOLcheapest, stainless steel, vv-350 ecig on the internet, and by the way mate what is a did ?

I have to assume its the same model I have been using for months with zero problems from this vendor

VZ VARITUBE-3 Mod/APV 510 (Body only) 3 to 6 Volt - E Cig : Joye eGo & eGo-T | Boge Leo | Cartomizers | E-Liquid | Electronic Cigarettes | eGo Tank

The did clones i use are clones of the real expensive did from greece



VZ 510 Rebuildable Atomizer Tank (DID Clone), Single Pc - E Cig : Joye eGo & eGo-T | Boge Leo | Cartomizers | E-Liquid | Electronic Cigarettes | eGo Tank

 

[terry w]

Yes after looking at the pics it certainly looks like they are exact,so basically a did is a rebuildable like the pheonix or bully ? mainly to be used for dripping ?

 

[mgmrick]

Yes after looking at the pics it certainly looks like they are exact,so basically a did is a rebuildable like the pheonix or bully ? mainly to be used for dripping ?

No they have tank on bottom. Real nice

 

[terry w]

yes they look cool,i may invest in one of those mate,do they use normal carts like a dct, and what size ? or do you have to buy special carts for it ?

 

[mgmrick]

No you make your own ss mesh wick and coil. At first it seems hard but after the first couple of times it is pretty easy to do it. And tons of you tube video's to guide you

yes they look cool,i may invest in one of those mate,do they use normal carts like a dct, and what size ? or do you have to buy special carts for it ?

 

[terry w]

ok cheers for that rick,you have been a great help...thanks buddy

 

[mgmrick]

ok cheers for that rick,you have been a great help...thanks buddy

enjoy that mod !