Cloupor 30W Box Mod OWNERS thread

[dhomes]

if i just received it and this happened i would contact the shop i bought it from and see if they could send me a new one it couldn't hurt to see what they have to say

@jomiz
I sent a support email a few minutes before posting here, i'll let you all know what happens

 

[Jomiz]

looking forward to it hope they can work it out

@jomiz
I sent a support email a few minutes before posting here, i'll let you all know what happens

 

[lukcy7]

@dhomes Did you happen to get any juice down in the 510 recess? That happened to me a couple times, and it would read check atomizer until I cleaned it out well.

 

[Muggs]

Guys the center pin on your rda's/rba's needs to be extended out a bit. That's it. It's not a broken unit it's a simple fix. Trust me.

 

[CurlyxCracker]

Guys the center pin on your rda's/rba's needs to be extended out a bit. That's it. It's not a broken unit it's a simple fix. Trust me.

This. Make sure your positive pin is out further than your 510 threading

 

[vibaka]

This. Make sure your positive pin is out further than your 510 threading

I have noticed the same thing, especially on my Russian 91.

 

[joecil]

Well mine arrived today from 101 vape in red. It is flawless as far as fit and finish goes. I tried all my attys, RBA and RDA on it and all fit and showed ohms reading. Now it so far has been easy to set and functions perfectly but again I've only been using it now for 4 hours. It does take on click to bring it out of sleep mode which I don't have a problem with. I've also found the ohm reading is pretty much dead on at this point.

Now I did have a J-Wrap for the Hana Modz V3 and found it is different enough for me to send it back for the clone skin as I was told to do. It was close but would of require some trimming in areas and a little short in others.

 

[dhomes]

@dhomes Did you happen to get any juice down in the 510 recess? That happened to me a couple times, and it would read check atomizer until I cleaned it out well.

hi lucky, thanks for the tip!

how did you fixed it?

 

[dr g]

So, how do you remove the cover over the chip?

 

[MrPlink]

So, how do you remove the cover over the chip?

If you can't figure that one out what are the odds access to the board will be a good thing for you?

not hatin, jus sayin

 

[dr g]

If you can't figure that one out what are the odds access to the board will be a good thing for you?

not hatin, jus sayin

let's just say that's not a concern by a long shot.
i'm just asking because it's always easier to not reinvent the wheel.

 

[CurlyxCracker]

let's just say that's not a concern by a long shot.
i'm just asking because it's always easier to not reinvent the wheel.

Use a pry tool, like one for iPhone screen repair

 

[dr g]

Use a pry tool, like one for iPhone screen repair

Ok. Is it hot glued?

 

[laurie9300]

Fired up my clone this morning and the screen is dead! It still fires, the up and down buttons don't seem to do anything, but it still fires.

And did I mention THE SCREEN IS DEAD!

I have pulled the battery, I will leave it out for a while and see off it resets, well report back soon........

 

[CurlyxCracker]

Ok. Is it hot glued?

Yes I believe

 

[CurlyxCracker]

Fired up my clone this morning and the screen is dead! It still fires, the up and down buttons don't seem to do anything, but it still fires.

And did I mention THE SCREEN IS DEAD!

I have pulled the battery, I will leave it out for a while and see off it resets, well report back soon........

Second case I know of. Vendor? How long have you had it

 

[MrPlink]

Fired up my clone this morning and the screen is dead! It still fires, the up and down buttons don't seem to do anything, but it still fires.

And did I mention THE SCREEN IS DEAD!

I have pulled the battery, I will leave it out for a while and see off it resets, well report back soon........

Oh goody, I may be the first but not only

http://www.e-cigarette-forum.com/fo...44-another-broken-kinda-cana-dna30-clone.html

 

[laurie9300]

Second case I know of. Vendor? How long have you had it

Got it yesterday through a co-op here in Australia, it was perfect out off the box, used it for a couple of hours last night...........

Left the battery out for 15 minutes, but no change.......

 

[laurie9300]

Oh goody, I may be the first but not only

http://www.e-cigarette-forum.com/fo...44-another-broken-kinda-cana-dna30-clone.html

Thanks for the link, maybe mine will re awaken too!

 

[CurlyxCracker]

Thanks for the link, maybe mine will re awaken too!

There's rumors of contacting clopour for a replacement.