e-smokeguru official thread

[imeothanasis]

I am sure that you will like short Iatty a lot Brem. It has now some more possibilities.

1. It doesnt get overflooded because liquid stays lower than before
2. You can turn cone much easier because it sticks out of the cap a lot
3. Its shorter
4. You will like the logo I hope. Only esmokeguru logo is there

 

[breminator]

I am sure that you will like short Iatty a lot Brem. It has now some more possibilities.

1. It doesnt get overflooded because liquid stays lower than before
2. You can turn cone much easier because it sticks out of the cap a lot
3. Its shorter
4. You will like the logo I hope. Only esmokeguru logo is there

I like Iatty cause his very special and intensive taste.
It sounds like you keep your eyes on the right things to make Iatty better.
How did we get informed about the grand opening?

 

[imeothanasis]

I try to keep updated all GG constructions Brem, thats why sometimes I make mistakes like the one with Ody bases. I try to not make the same thing but a little better everytime even for older GG constructions.

Vasilis miss only the center pin of those Iatties. I will send them to him in 2-3 days, so I believe that next day he will announce the sales

 

[breminator]

Thanks for these good news, Imeo.

 

[imeothanasis]

be well buddy

 

[UTUTUT]

anyway, i have a problem with iatty imeo

please look at attached file



often my iatty can't seal the liquid perfectly between refilling cap and tank (mark →)

i can see that the liquid is leaking so pocket on my pants get wet.....

the other things are perfect great taste, but.....

how can i solve it ?

i have inserted o-ring there, but it looks soooooooooo bad

should i order new refilling cap??

 

[Sad Society]

telemachus or Tilemahos in Greek will be the new atomizer for Esterigon. Odysseus was the fat one, Penelope the thin one, Ithaka the longer one and Tilemahos the mediul one. We named them proper I think!

I thought I read that a bigger base Penelope will be made to match the diameter of Esterigon. Please correct me if I'm wrong on this.

 

[Sad Society]

anyway, i have a problem with iatty imeo

please look at attached file

View attachment 338309

often my iatty can't seal the liquid perfectly between refilling cap and tank (mark →)

i can see that the liquid is leaking so pocket on my pants get wet.....

the other things are perfect great taste, but.....

how can i solve it ?

i have inserted o-ring there, but it looks soooooooooo bad

should i order new refilling cap??

The cap should be fine...I would think. If it is leaking on top then the O-ring is not doing it's job and you need a new one. The pic you have looks like the top O-ring may be too big and you are not able to screw the top cap down all the way. Maybe use a less thicker O-ring.

 

[Risto]

The short Iatty esmokeguru edition will be ready in about 1 week or less UT

I already wrote here that Iatty Upper Plastic is not good in my new Iatty.
Or the Iatty Cone.
Threading (screw cutting; thread cutting; riffing) those parts are not good.
See the posts: # 2501 and # 2665 and # 2753 also.
Sorry, but no one ever responded to my previous posts.

I have to buy those parts.
First, I have to buy Iatty Upper Plastic, because I suspect that this part is not good.
My question:
Whether Iatty Upper Plastic and Upper Plastic for the short Iatty esmokeguru edition are compatible with each other?

 

[UTUTUT]

The cap should be fine...I would think. If it is leaking on top then the O-ring is not doing it's job and you need a new one. The pic you have looks like the top O-ring may be too big and you are not able to screw the top cap down all the way. Maybe use a less thicker O-ring.

originally there are no o-ring.. so i don't want to insert o-ring there,

but in this case, should i insert o-ring ??

 

[monkkx]

Sad society, Telemachus is the candidate name of this large Penelope you described.

 

[Sad Society]

originally there are no o-ring.. so i don't want to insert o-ring there,

but in this case, should i insert o-ring ??

I don't know then. I don't own iatty, but all my GG atty's have an O-ring on top cap. If one shouldn't be there, then why add one? Unless, like you say it is leaking. Maybe someone else who owns iatty can chime in.

 

[UTUTUT]

I don't know then. I don't own iatty, but all my GG atty's have an O-ring on top cap. If one shouldn't be there, then why add one? Unless, like you say it is leaking. Maybe someone else who owns iatty can chime in.

oh yes all of my gg atty's have an o-ring there too, except iatty and UFS...

my iatty hadn't leaked but recently it happen....

anyway, thanks your reply

 

[Risto]

I am sure that you will like short Iatty a lot Brem.
..........4. You will like the logo I hope. Only esmokeguru logo is there

The short Iatty esmokeguru edition will have the logo.

Will there be wing this, or maybe it will looked like this?

 

[bacc.vap]

No, the Iatty does'nt have an oring for the top cap. The top cap does'nt seem to screw down quite all the way, like yours in picture, but I think that's sort of normal. I have'nt had leaking issues with mine. You could maybe try an oring that fits up inside the cap if it's not good to have one at the base of the threads.

 

[steliosss]

I already wrote here that Iatty Upper Plastic is not good in my new Iatty.
Or the Iatty Cone.
Threading (screw cutting; thread cutting; riffing) those parts are not good.
See the posts: # 2501 and # 2665 and # 2753 also.
Sorry, but no one ever responded to my previous posts.

I have to buy those parts.
First, I have to buy Iatty Upper Plastic, because I suspect that this part is not good.
My question:
Whether Iatty Upper Plastic and Upper Plastic for the short Iatty esmokeguru edition are compatible with each other?

Everything is the same ti new Iatty buddy, except the new shorter tube with the GG-ESG logo.
So you can replace whatever you want to each other and make your experiments

originally there are no o-ring.. so i don't want to insert o-ring there,

but in this case, should i insert o-ring ??

Yes You can put a 13x1,5 o-ring (it's the same as the base)
Try it... as bacc.vap said

 

[imeothanasis]

solution is easy UT, no worries. To understand better, this small 0,2mm gap exists on UFS, Ithaka, Odysseus. I made it like this to avoid the need of an o-ring around the neck of the body. So, if you dont like the o-ring around the neck of the body then you can put an o-ring to the botton of the cap (where the cap touches the body when its screwed) and problem solved

anyway, i have a problem with iatty imeo

please look at attached file

View attachment 338309

often my iatty can't seal the liquid perfectly between refilling cap and tank (mark →)

i can see that the liquid is leaking so pocket on my pants get wet.....

the other things are perfect great taste, but.....

how can i solve it ?

i have inserted o-ring there, but it looks soooooooooo bad

should i order new refilling cap??

 

[imeothanasis]

I thought I read that a bigger base Penelope will be made to match the diameter of Esterigon. Please correct me if I'm wrong on this.

tilemahos will be a little different than Penelope Sad. But as you said, it will have the same diameter of esterigon to fit there perfectly

 

[imeothanasis]

yes, compatible Risto. As for your issue, just contact to esg

I already wrote here that Iatty Upper Plastic is not good in my new Iatty.
Or the Iatty Cone.
Threading (screw cutting; thread cutting; riffing) those parts are not good.
See the posts: # 2501 and # 2665 and # 2753 also.
Sorry, but no one ever responded to my previous posts.

I have to buy those parts.
First, I have to buy Iatty Upper Plastic, because I suspect that this part is not good.
My question:
Whether Iatty Upper Plastic and Upper Plastic for the short Iatty esmokeguru edition are compatible with each other?

 

[imeothanasis]

no wings and not like this too Risto. Only vasilis can answer that because he may doesnt want to let me tell you

The short Iatty esmokeguru edition will have the logo.

Will there be wing this, or maybe it will looked like this?