GG series o-rings guide
- Thread starter imeothanasis
- Start date
- th_trl_thread_readers 0
-
- Tags
- provari
- Status
I was using my UFS last night and it instantly started leaking heavily into the collection tank and flooding the atomizer. I took the whole unit apart and realized that the connector pin is missing 2 o rings 
I checked out this thread and see that I need the 2mm/1mm for inside the pin and 4mm/1.5mm for the outer part of the pin. I have searched this forum and google high and low and can not find any site that sells both o rings. oringsUSA has the 2mm/1mm but not the 4mm/1.5mm. They do have a 4mm/1mm do you think that will still be sufficient. If not can someone tell me a site where I can just buy these things in bulk and not have to worry about it again. I am going to try ace hardware after work but I think that may be a longshot. Any help much appreciated. Thanks.
I checked out this thread and see that I need the 2mm/1mm for inside the pin and 4mm/1.5mm for the outer part of the pin. I have searched this forum and google high and low and can not find any site that sells both o rings. oringsUSA has the 2mm/1mm but not the 4mm/1.5mm. They do have a 4mm/1mm do you think that will still be sufficient. If not can someone tell me a site where I can just buy these things in bulk and not have to worry about it again. I am going to try ace hardware after work but I think that may be a longshot. Any help much appreciated. Thanks.
Nevermind I did not see the 4mm/1.5mm towards the bottom . oringsUSA does have everything you should need for the UFS 
edit: after I purchased I found this site http://www.mcmaster.com/ you can get 10 times the amount for the same price.
. oringsUSA does have everything you should need for the UFS edit: after I purchased I found this site http://www.mcmaster.com/ you can get 10 times the amount for the same price.
Last edited:
Thanasi from iatty missing the under the center post o-ring
its a 3X2mm but 3X1,78 work fine also
its a 3X2mm but 3X1,78 work fine also
What is the size and material of the Ithaka Insulator Plastic i am going to pick up some o-rings thought i might be able to get a few plastic insulators as well thanks ahead of time . adam
great move bb
also I forgot the o-ring around the AD cap where the AD ring sits. Its a 14x1
also I forgot the o-ring around the AD cap where the AD ring sits. Its a 14x1
Thanks for adding the list Imeo! 
To be honest, on the video, I was a bit worrying about the reliability of the brass contact/switch o ring, because it's tightly flatened, but now I have seen one for real, and how fat it is, I don't worry anymore...
To be honest, on the video, I was a bit worrying about the reliability of the brass contact/switch o ring, because it's tightly flatened, but now I have seen one for real, and how fat it is, I don't worry anymore...
Is it possible to get the specs for the Tilemahos V2 22mm o-rings this would help a lot Thanks Adam
Hi there,
which material are the GG o-rings made of? I need two for my new Tilemahos brass AD Ring. I didn't know that the AD Ring comes without o-rings ;-)
But i can get two o-rings in my company.
But there i can choose between following materials:
- NBR70
- FPM75
- MVQ70
- NBR90
- PTFE
Thanks and Greetings from Germany
which material are the GG o-rings made of? I need two for my new Tilemahos brass AD Ring. I didn't know that the AD Ring comes without o-rings ;-)
But i can get two o-rings in my company.
But there i can choose between following materials:
- NBR70
- FPM75
- MVQ70
- NBR90
- PTFE
Thanks and Greetings from Germany
AD ring comes with o-rings Entry. Your seller just forgot them. By the way, you can buy NBR o-rings. Thats what I use
Anyway, every time you buy a GG construction or spare, better buy a set of o-rings. They are very cheap
Anyway, every time you buy a GG construction or spare, better buy a set of o-rings. They are very cheap
all brass parts I purchased for estirigon and tilemahos came without o-ring either ... it's a pitty since I'm part of those thinking it would be included for sure ...
I always send the nessesary o-rings to my sellers monk. Yes its a pity. Let me send an e-mail about this issue to all my sellers to be sure that this will not happen again
- Status
