Those look like they would actually have to be tipped over much more than a Stardust since they aren't tapered at the top.
Gotvapes Stardust: How to re-wick and replace the coil
- Thread starter RockinRobbieSF
- Start date
- th_trl_thread_readers 0
- Status
Comes with longer wicks that you can use as is or trim if you like.
discountvapor.com has them for pre-order for $7.99, tube replacements at $1.49
and the insides at $2.49. This place has some nice stuff
http://www.e-cigarette-forum.com/forum/discountvapers/284729-new-product-releases-7.html#post6084120
post #65 tells about them
Also check out the CE4+ for $2.99 in the "Bargain Bin"
and the insides at $2.49. This place has some nice stuff
http://www.e-cigarette-forum.com/forum/discountvapers/284729-new-product-releases-7.html#post6084120
post #65 tells about them
Also check out the CE4+ for $2.99 in the "Bargain Bin"
Last edited:
I asked them about the date for the replacement parts that had March 2013, Just got a reply
email saying it was a mistake and all items will be in on Tuesday May 15.
Also .... I paid with wepay and got the bill in about 20 minutes no signup needed.
email saying it was a mistake and all items will be in on Tuesday May 15.
Also .... I paid with wepay and got the bill in about 20 minutes no signup needed.
Last edited:
Bruce at COV sells wick for the Odyssues, its 2mm wick and good stuff,,, I think Chris at Gotvapes also sells it,,, Kanthal can be had on Ebay,,,, 32-34-36 Kanthal all works fine,
I brought some awhile back from COV but used it all trying to learn how to rewick the Stardust 
I never seen it at Gotvapes but will check and see if they also sell it. I got the kanthal from ebay also and
still have plenty left, thanks for the gotvapes tip.
I never seen it at Gotvapes but will check and see if they also sell it. I got the kanthal from ebay also and
still have plenty left, thanks for the gotvapes tip.
discountvapor.com has them for pre-order for $7.99, tube replacements at $1.49
and the insides at $2.49. This place has some nice stuff
http://www.e-cigarette-forum.com/forum/discountvapers/284729-new-product-releases-7.html#post6084120
post #65 tells about them
Also check out the CE4+ for $2.99 in the "Bargain Bin"
The CE4+ are ver.1 & have some mfg. issues. Not that they can't be cleaned up... Just sayin'.
Yes I seen that, but figured I take a chance and get a few to see. Don't think they would
sell them if they were that bad....I hope
If you brought just the empty tube and mouthpiece elsewhere it would cost over $2.00.
At $2.99 I'm hoping that xmas came early this year
Last edited:
View attachment 100365Now we have the Ego CE5 and they have rebuildable cores !
eGo CE5+ Rebuildable Clearomizer
View attachment 100377
eGo CE5+ Rebuildable Clearomizer
View attachment 100377
Last edited:
Hey Robbie, I've got an easier method to remove that pesky botton ring and you don't need to put masking tape on them (by the way those things are called slip-joint pliers - Channel-locks in the trade).
1) For those of you that don't have lighters anymore, take a trip to your local store and buy a Bic.
2) Heat the metal for a few seconds. The plastic can withstand a bit of heat, but be careful not to overheat (need I say?)
3) Be prepared with a paper towel or face towel. (So you don't burn your fingers - duh.)
4) Twist right away and off it comes!
It worked very well on the two I tried today. Haven't tried it on the new style Stardust yet, but one of the two had super-glue in the ring from sealing cracks and the ring came right off, where it would not budge using other methods.
This also works for the top ring (if you ever need to remove it), although it seemed to need more heat.
The fit is not as snug afterward - I suppose a dab of Elmers glue would help here. Ed. (Tried it - it does.)
But you'll never have to pull hard again!
1) For those of you that don't have lighters anymore, take a trip to your local store and buy a Bic.
2) Heat the metal for a few seconds. The plastic can withstand a bit of heat, but be careful not to overheat (need I say?)
3) Be prepared with a paper towel or face towel. (So you don't burn your fingers - duh.)
4) Twist right away and off it comes!
It worked very well on the two I tried today. Haven't tried it on the new style Stardust yet, but one of the two had super-glue in the ring from sealing cracks and the ring came right off, where it would not budge using other methods.
This also works for the top ring (if you ever need to remove it), although it seemed to need more heat.
The fit is not as snug afterward - I suppose a dab of Elmers glue would help here. Ed. (Tried it - it does.)
But you'll never have to pull hard again!
Last edited:
I'm curious, will these stardust's fit a Buzz, or a VariCool Box mod? They don't look like they will, but I was just curious. don't want to waste money on them if they don't.
You have to pass the flame real fast. The plastic deforms very quickly.
Concentrate on the very end of the ring and you shouldn't have any deforming - none of mine deformed and they all came off very well. The only drawback is the slightly looser fit (you may want this), which can be easily fixed with a small drop of Elmers glue.
Hey Lynch, Could you put a link to where you bought this E-Turbo 2.0 They look great and I want one or two
Thanks
Thanks
They are from a china seller and you need to buy 100 or more, they should be selling them here soon.
These are good and the parts are interchangeable with the revive E1.
http://www.discountvapers.com/e3-rebuildable-clearomizer/
Last edited:
Posted these on another thread , these are easy if you dont want to make your own Rebuildable Atomizer Coils - Avid Vaper
- Status
Similar threads
- Locked
- Locked
