- Status
Just another word of warning for GP users. I screwed on an atty too tight and while trying to loosen the screw of the top switch, I got a nasty cut on the side of my thumb. Didn't even notice the cut until I saw blood smeared along the side of the tube.
The screws below the top cap can be very sharp. Use caution when applying pressure.
This isn't the first time I've sliced my hands with the GP. With the lux, I had the top cap on too tight and while trying to loosen it with the button off, I sliced up the side of my palm on the bottom of the tube around the threading.
The threading on the tubes can be very sharp. Use caution when applying pressure.
By cuts I mean something along the lines of a nasty paper cut, not along the lines of losing a finger. So yeah, I'm fine and it's not a big deal but it's avoidable.
Warning? "Caution" I guess!
My Paps tubes are just fine... no sharp edges anywhere... None in any of the Six Units that I possess. And unless I use a wrench (LOL) to tighten anything -- I don't think I could make anything so difficult that I cannot remove it effortlessly.
Thanks for the heads up anyway!
I would buy it but, I can not stand GM fake ... GP tubes near PAPS. And, as Qbrudda mentions, it may be a bit steep. But, good find TonywhomlikestoDestroyshti.
Also wanted to share with the thread, I love refinishing my own mods and have a couple GP that I HAD in line. I realized i have no time to do all plus building a vape table, putting single mod holders together, and my other stuff. I finally got smart and sent 2 of my very favorite PAPS to a buddy for catch up as they are my favorite of about 11 complete PAPS and muh LUX's.
Here is a picture of them.
Not an SnP or KF guys but the micros are quite easy to wrap.
I made this one on a 1.65mm drill bit which I think is a 1/16th.
That looks incredible! How does it not short out?
Hey UKPaul, i hope You are going to tell us a little more about that microcoil for example, what ohm do You get out of it, how areyou going to get some wick through that tiny hole?
Sendt fra Tapatalk 4
Sendt fra Tapatalk 4
Cm7b5, is this one sweet bottom button or what?
I was a fan of the K Lite upon receiving my first 2 from inTaste. As such, I ordered a 3rd for the PAPS.
This is my 1st GP product and it will not be my last . . . Enjoy.
- Andy
Micro coiling produces better flavor and vapor for most.
The coils are intended to touch. And I would guess if he is using .,28 he is around 1.7-2.0ish ohms. 1/16th it's usually max size. A bit smaller for some.
The nice thing is they don't get sub ohm hot.
The coils are intended to touch. And I would guess if he is using .,28 he is around 1.7-2.0ish ohms. 1/16th it's usually max size. A bit smaller for some.
The nice thing is they don't get sub ohm hot.
Here's a find: if you need new O-rings for the inner diameter of the SnP (the 4 O-rings through which the Diver passes), the O-ring pack for the VmodXL, VPA-068, includes two of the correct size. I had a spare pack from my Vmod days, and ruined one of the 4 spares - after ruining all 4 of the first set - so I dug through and found these.
VMOD XL / VMOD 2.0 Seal Kit
VMOD XL / VMOD 2.0 Seal Kit
Guys, I'm giving up on the SnP tank until I start seeing some videos. I've just shredded the last of the inner O-rings with the Cartodriver tool. I figured I would slide it through on its own, to see if it would fit. It just won't go through, and when it squeezes through a few millimeters, it shreds the O-rings.
My switch button sticks frequently when I was using it today. How do I disassemble the switch to inspect what's going on?
My SnP and Diver arrived today! No pre-built coil for the Diver, sadly, but that's cool.
One question: the Diver came with three spare bundles of wire, but they're not labeled. How do I tell these apart, and which should I use?
One question: the Diver came with three spare bundles of wire, but they're not labeled. How do I tell these apart, and which should I use?
I noticed it was pretty darn tight as well. Used some VG to lube up the orings and driver, worked pretty well.
I did lube them, but every time the Diver would make it through, it would slice the inner part the O-rings off.
2 x bundles are NR and one is Kanthal 30g. The Kanthal one is "marked'... there's something written in pen (mine was in Greek!).
Got my lux today, awesome vape mail
But, i seem to have a problem with the top-pin adjustment. I snug up the outer pin to make good contact with the atomizer, but even with the adjustable pin tightened all the way down, i get 1mm gap between the top-cap and the 350 tube.
any suggestions? i took a look at the domo page and their v2.5 pin upgrade kit comes with a 1.2mm as well as 2.2mm adjustable pin. My extras baggy had a spare spring and pin, but both are the thicker 2.2mm versions. did someone forget to include the thinner pin (which i think would solve my gap issue)?
thanks,
chris
But, i seem to have a problem with the top-pin adjustment. I snug up the outer pin to make good contact with the atomizer, but even with the adjustable pin tightened all the way down, i get 1mm gap between the top-cap and the 350 tube.
any suggestions? i took a look at the domo page and their v2.5 pin upgrade kit comes with a 1.2mm as well as 2.2mm adjustable pin. My extras baggy had a spare spring and pin, but both are the thicker 2.2mm versions. did someone forget to include the thinner pin (which i think would solve my gap issue)?
thanks,
chris
Got my lux today, awesome vape mail
But, i seem to have a problem with the top-pin adjustment. I snug up the outer pin to make good contact with the atomizer, but even with the adjustable pin tightened all the way down, i get 1mm gap between the top-cap and the 350 tube.
any suggestions? i took a look at the domo page and their v2.5 pin upgrade kit comes with a 1.2mm as well as 2.2mm adjustable pin. My extras baggy had a spare spring and pin, but both are the thicker 2.2mm versions. did someone forget to include the thinner pin (which i think would solve my gap issue)?
thanks,
chris
The screw in that spare bag is shorter. Just swap it with the one fitted in the top-cap.
______________________________________
CONGRATS for ur Lux
- Status
Similar threads
- Locked
