GP Series by VapourArt - Official Thread for GP Spheroid, GP PAPS, X, GP Piccolo, GP SnP and more - Part 1

[landman2k1]

The reason I'm holding off a Prometey-2 purchase. Ah, it went live today.

Delayed until the 7th apparently. I too am holding out on other atties. Must say, the hype on the Spheroids is well deserved. Been trying to get the wife into a rebuildable and this is the first one she has taken to. She liked the kayfuns but complained of them being to heavy, lol.

So... the piccolo/sphero will be her setup if I can get her to make the switch to mechs.

Question for the Piccolo owners out there, how long will the 14500 batts last? Yes, I realize the scope of the question, so let's put it in terms of juice consumption. Will the battery last all day (for her, about 3ml of juice)?

 

[Jonny5]

I think the batteries last about the same as 18350's if that helps. Should probably keep a spare for 3 ml.

 

[landman2k1]

Grabbed my first "Electronic" Mod a few minutes back



I had vowed to remain a 'Mechanical Guy' - but all your Provari pictures made me think probably I was missing something.

May I ask what vendor? I have been eyeing this guy as well.

 

[perseas]

O-rings.... shredded!

When you insert the cartodriver alone, are the O-rings shredded too?

When you put your RDA connected with the cartodriver, do they have the same thickness at their connection?
Or, the outer lips of the RDA, have a slight protrusion with sharp edges?

 

[qorax]

When I am submerging anything into my SnP, I always:

Apply generous amounts of juice to the ORings ( orange )
Keep SnP tank fully assembled
Insert given cartodriver into the Top of submersible atty of choice
Apply generous amounts of juice to said atty.
Insert atty from TOP of SnP tank
Apply pressure to push atty through.

Note: The first time I inserted an atty through the SnP it was a struggle. Skimmed off a piece of the ORing. It didn't matter though, as she seated well, and produced zero leaks.

I dropped my SnP in warm water (10 minutes) then slid the 'well lubed' Diver + CartoTool thru.



They went in smoothly. Stock O-rings. Nothing changed / modded.

 

[qorax]

May I ask what vendor? I have been eyeing this guy as well.

Direct from markbugs.com, it went on sale today at 20:00hrs. GMT (3PM my time, New York / Toronto). Heads up thru Vapor Wall.

 

[Nach]

When you insert the cartodriver alone, are the O-rings shredded too?

When you put your RDA connected with the cartodriver, do they have the same thickness at their connection?
Or, the outer lips of the RDA, have a slight protrusion with sharp edges?

The cartodriver doesn't shred the o-rings, but is extremely tight. even coating it with VG didn't seem to help.

I feel that the Diver shaved those o-rings at the juice inlets. I only see one way to resolve it, and that's to push the base of the Diver v2 into the bottom cap from the inside and then attach the top cap over the Diver. This way the juice inlets wont pass over any o-rings.

The cartodriver seems fairly flush with the Diver. It does; however, have a lot of scars from machining.

 

[Jojobo]

so if this is the case...how do you maintain the coil and wick without breaking down the whole tank??

 

[digitals]

Grabbed my first "Electronic" Mod a few minutes back



I had vowed to remain a 'Mechanical Guy' - but all your Provari pictures made me think probably I was missing something.

Nice Q. DNA 20? I've heard of these. Do, as I know you will, provide an extensive review dazzled with pics upon receipt.

 

[digitals]

so if this is the case...how do you maintain the coil and wick without breaking down the whole tank??

What is this question in reference to Jo?

 

[digitals]

Direct from markbugs.com, it went on sale today at 20:00hrs. GMT (3PM my time, New York / Toronto). Heads up thru Vapor Wall.

Whew! 250€! Very nice indeed!

 

[chadsmo]

Grabbed my first "Electronic" Mod a few minutes back



I had vowed to remain a 'Mechanical Guy' - but all your Provari pictures made me think probably I was missing something.

Awesome. I see they fixed the top cap. Does this have the fixed centre pin too?

 

[Jojobo]

What is this question in reference to Jo?

getting the diver2 in without stripping the orings ... if you have to take the top cap off and feed the base of the diver thru the base of the SnP thru the inside of the SnP, how do you then slide the diver2 thru the bottom of the base to maintain the coil and wick and then slide it back up when you are done?

 

[Deas]

Question for the Piccolo owners out there, how long will the 14500 batts last? Yes, I realize the scope of the question, so let's put it in terms of juice consumption. Will the battery last all day (for her, about 3ml of juice)?

I vape 2-2.5 ml/day and it's about 1.5 14500 700mah Aw Imr batteries.

 

[digitals]

getting the diver2 in without stripping the orings ... if you have to take the top cap off and feed the base of the diver thru the base of the SnP thru the inside of the SnP, how do you then slide the diver2 thru the bottom of the base to maintain the coil and wick and then slide it back up when you are done?

I don't believe accessing the Diver wick/coil is possible this way. Not like the Sophia, where you can push the atty all the way through to maintain.

I could be wrong?

Edit: unless of course your carto driver tool is attached to the Diver, which would keep everything sealed off.

 

[Woody7781]

O-rings.... shredded!

That looks like the Goldschlager of e juice you got in there. Little bits of oring for your vaping pleasure.

 

[Idaholandho]

Direct from markbugs.com, it went on sale today at 20:00hrs. GMT (3PM my time, New York / Toronto). Heads up thru Vapor Wall.

Such a great VV. Nice Q.

 

[qorax]

Whew! 250€! Very nice indeed!

$376.81 CAD to be exact, as per Paypal. It is a bounty indeed. And to make it possible took Jess shopping yesterday, got her $900 worth... else, this transaction would have got me "Off With Your Head"!

 

[Idaholandho]

Awesome. I see they fixed the top cap. Does this have the fixed centre pin too?

I think he wants to keep everything as small and flat as possible, I think his upcoming new 22mm is also going to be fixed. A floating pin would be so nice.

Edit - I stand corrected, A bit of chatter on the UK thread that he was sticking to fixed. I cant see his new mod being fixed in this case.

 

[qorax]

Awesome. I see they fixed the top cap. Does this have the fixed centre pin too?

Yep. The top cap has thru-n-thru air channels and it's now a Telescopic 510.