GP Series by VapourArt - Official Thread for GP Spheroid, GP PAPS, X, GP Piccolo, GP SnP and more - Part 3
- Thread starter perseas
- Start date
- th_trl_thread_readers 0
- Status
So I was enjoying castle long quite a bit... So i loaded up my heron with it, and yeah... Not as good as in my dripper. Heron is set at 1.1ohm, i think. Dripper is about .5.
However, i did throw my 510 onto the x and on the heron and swapped them onto each other's devices. Like my dripper so much more on the X. But now my poor heron is on the beater. I so need another X.
Anyone know some high quality 23mm drippers?
However, i did throw my 510 onto the x and on the heron and swapped them onto each other's devices. Like my dripper so much more on the X. But now my poor heron is on the beater. I so need another X.
Anyone know some high quality 23mm drippers?
I wish you well Cucco, and am sure it will all go fine for you. Wish I lived nearby, and I'd stop over with some flowers for you.
Hello my GP Family!
Sorry to hear, that 'life things' are costing some of our Family extra $s.
Those darn 'life things'....
If hope you guys don't mind, I'm going to tell my GP Family a little 'life thing' that has me a bit stressed....
On Tuesday, I am scheduled to have a breast tumor removed. Being a widow, pretty much s*cks. But, times like this, being a widow s*cks even more. Scary times, were a lot easier with my man by my side. I am a bit surgery phobic. When I was eighteen, I had a minor surgery go very wrong. For a brief moment, I was conscience (or not), and could see and hear all the commotion that was happening in response to my critical state. It is still very vivid in my mind. I have had a few surgeries since, without any major complications. But, each has resulted in significant pre-surgery stress. For the later surgeries, Hubby was there. Hubbies make everything better. At times like this, some may say, "I want my Mommy". Right now, all I can think is, "I want my Hubby.".
Even for a tough old broad like me, things can be scary. But, it's all good!
Lots of great well wishes going out to our Cucco. As always you are in my mind and heart. I also wish I could give a great big hug and squeeze to comfort you. I know all will go well and since your are strong and stubborn you will recover fast and back on your feet. Love ya girl...........
I've been getting hot buttons recently on my paps v3. I'm running a .92 resistance kayfun on the 18650 ss with vtc5s. I have the lux gpin and switch contact and had the spring silver coated and the button rhodium coated. Any suggestions?
Cucco. Life throws so many curveballs our way at various times of our life. You have seen your share. But you will conquer this phase and be remembering the memories of lost loved ones for a while to come. Prayers and good vibes your way.
Spydro, my sympathies in this day and every other. May the memories continue to burn deep as a beacon.
First thing to try to determine this as there may be a few suggestions. How is the button with a different atty? Need to rule out the cause.
Today is a 12th Anniversary for me. Its not an anniversary to be celebrated, just one that is remembered as when I started my life over again as a bachelor.
Sending hugs to you, my friend.........
I've recently had a hot switch a couple of times with the v3 with vtc5's also, and imo it usually had something to do with the build. Other times it's the battery. Maybe that vtc5 is too much for that build. When you use an aw imr 650 with that single coil build, does the switch still get hot?
Lots of great well wishes going out to our Cucco. As always you are in my mind and heart. I also wish I could give a great big hug and squeeze to comfort you. I know all will go well and since your are strong and stubborn you will recover fast and back on your feet. Love ya girl...........
Perfectly said, mirrors my thoughts exactly.
We WILL all be with you.
If it's the same after checking what Yankee said then clean the switch. Soap and hot water, then let it dry completely. Even just a trace of water is not good. Even if this is not the cause it is a good habit to get into. I did have this problem quite awhile back on my v2.5 and cleaning the switch made it good as new.
I do know that Kidney Puncher sells has a limited selection of o-rings. I haven't ordered any from them yet to see if they are decent. But that is about the only site I've ever seen them listed. They also have 10mm, 15mm, 16mm and 18mm sizes.
17mm Black O-Rings 10 Pack - Kidney Puncher
Thanks GP fam! I tried a bunch of different attys and was still getting a hot button. After cleaning with soap and water and thoroughly drying with a microfiber towel and air, no more hot button. Thanks again fam!
- Status
Similar threads
- Locked
- Sticky
