High end RTAs

[Akrotiri]

I dont understand what you are on about? If the glass spins the top cannot be stuck?

i know its really weird never had a problem like this but i never vaped an atty for so long without removing to clean it.

It might not actually be spinning might just be my hand slipping

 

[Yonjuro]

do you have the new o-ring or the old ones?

 

[Akrotiri]

if i break the glass will this end? I have 6 spares so i don't care i just want this thing apart.

 

[Ragnar94]

So the top cap on my skyline is stuck and the 510 adapter from provari is stuck to connector pin (even though I removed the screw) Tried everything freezer, rubber gloves, nothing works. I'm wondering if I should just break the glass to get it off since I have 6 spares. Can anyone offer any advice this is so frustrating.

If you have to break it, break it mate, youve got six spares

 

[Akrotiri]

do you have the new o-ring or the old ones?

i have from batch 2 so it must be the new ones

 

[Yonjuro]

get some rubber kitchen gloves, turn the atty upside down, grip the glass and top cap firmly in your hand and use force to unscrew (counter clockwise the base)

Alternatively you can take off the AFC ring and insert a 2mm screwdriver though both openings. This will create a lever that will allow you to unscrew the base.

 

[Akrotiri]

well its not the orings for sure, I broke the glass but both top and bottom caps still stuck...

 

[Yonjuro]

well its not the orings for sure, I broke the glass but both top and bottom caps still stuck...

bummer - that was your pic on the ESG group page I presume?

 

[Akrotiri]

nope I don't have facebook. Am I not the only one with this issue?

 

[Yonjuro]

You say that the top cap is still stuck - It is one piece with the chimney section - it doesn't come off. - assuming you are not taking about the piece that allows you to take out the drip tip assembly??

 

[Yonjuro]

nope I don't have facebook. Am I not the only one with this issue?

I haven't heard of anyone with the new o-rings having a problem.

 

[Akrotiri]

You say that the top cap is still stuck - It is one piece with the chimney section - it doesn't come off. - assuming you are not taking about the piece that allows you to take out the drip tip assembly??

Yes I'm taking that off. I know the chimney/topcap is 1 piece It simply isn't unscrewing.

 

[Yonjuro]

Yes I'm taking that off. I know the chimney/topcap is 1 piece It simply isn't unscrewing.

What's not unscrewing ?? - the deck?

 

[Akrotiri]

What's not unscrewing ?? - the deck?

The base and the top/ chimney. Even though I have this atty for about 2-3weeks it's the first time since getting it I removed it from my mod and took it apart for a proper cleaning.Thats how good of a vape it's been for me so basically I'm still within the learning curve with this atty.

How do u go about taking it apart I don't know what I'm doing wrong or if it's stuck but I can see some of the bottom threading of the chimney.

 

[Yonjuro]

okay..

1. Firmly hold top section
2. unscrew deck anti clockwise
3. if the deck doesn't come free, remove AFC ring and insert a 2mm screwdriver between the slots to act as a lever.
4. Once deck is removed, screw down JFC as far as it will go, and using your little finger, spin out the chimney jfc piece.

you will then have

1. A deck
2. A chimney
3. a tank top piece that is joined to the outer housing of the chimney. This is one piece

 

[DragonNC]

I don't know why but for MTL i can't get better tank then kayfun v3 mini.....

 

[Ragnar94]

who was after a single deck for the hussar here? Single deck for Hussar RTA - Topvape Webstore

 

[Akrotiri]

okay..

1. Firmly hold top section
2. unscrew deck anti clockwise
3. if the deck doesn't come free, remove AFC ring and insert a 2mm screwdriver between the slots to act as a lever.
4. Once deck is removed, screw down JFC as far as it will go, and using your little finger, spin out the chimney jfc piece.

you will then have

1. A deck
2. A chimney
3. a tank top piece that is joined to the outer housing of the chimney. This is one piece

Alright thnks yonjuro turns out I screwed that chimney way too tight. I used a 5mm socket to get it separated finally.
Only problem now is that the juice control is stuck in the open/up position

 

[Yonjuro]

Alright thnks yonjuro turns out I screwed that chimney way too tight. I used a 5mm socket to get it separated finally.
Only problem now is that the juice control is stuck in the open/up position

I dont understand your question. You said you used a socket to separate the separate the chimney - that is the juice flow control ??

 

[Akrotiri]

Vassili told me just to mail in to him, which I am tomorrow. ESG has good customer service so they'll take care of it. In the meantime I'm using my backup but with the DTL deck and I have to say I think I like the increased airflow better than the mtl..