Here's a good pic of the deck, you can see the plastic insulator under the gold + post
I think I am missing the positive post insulator. Would that cause me to get an atomizer short message?
Hussar RTA single coil deck (attack of the clones)
- Thread starter rifky
- Start date
- th_trl_thread_readers 0
- Status
I think I am missing the positive post insulator. Would that cause me to get an atomizer short message?
From my exp its from a very thin gold layer. Brass will be soon became oxidation and turning dark. Its seem not. So I assume its a just a gold layer
Yes, maybe it fell out when you changed the pin? It has to be there or it will definitely not work
Yes, maybe it fell out when you changed the pin? It has to be there or it will definitely not work
That makes me feel much better! At least I know what the problem is. I will do a search of the area around my desk when I get back home tomorrow night. If I can't find it, I'll just order another one. It's a good flavor tank. I wish they came with extra insulators.
It has to be there some were. When I lose little parts, I get out my magnifying glass, Helps me a lot!
@JustWondering1 apart from the insulator on the deck, you should have a grey insulator on the top and the bottom of the new 2mm pin you are changing out for the 3mm, just did mine and is working fine.
Only home for the weekend, so just did a quick build, flavor not really there and got a metallic ting to it, could be because I rushed cleaning it though, will play more with it when get back to my 2nd home Monday.
Only home for the weekend, so just did a quick build, flavor not really there and got a metallic ting to it, could be because I rushed cleaning it though, will play more with it when get back to my 2nd home Monday.
I'm glad you received yours while you are home! I'm sorry you aren't getting the good flavor. I just put mine in hot water and liquid dish washing soap for 30 minutes, let it dry on paper towels, built a kanthal coil for it, inserted KGD wick and filled it. The flavor was good from the first draw, but it got better and better the more I vaped.
It could be I didn't wash it well enough, or because not using my normal building supplies, all that is back in des moines, so found some old wire KGD out here, but I do like the draw on it, and apart from the top looking to big with drip tip, I do like the looks of it, if gets better, will sure be getting the other top cap for it
It could be I didn't wash it well enough, or because not using my normal building supplies, all that is back in des moines, so found some old wire KGD out here, but I do like the draw on it, and apart from the top looking to big with drip tip, I do like the looks of it, if gets better, will sure be getting the other top cap for it
I was able to solve the wide bore drip tip issue by putting one of my 510 drip tips in the drip tip that is part of the standard top cap.
This is what it looks like with this tiny tip
$1.70 Stainless Steel 510 Drip Tip for Nipple RDA - 9mm at FastTech - Worldwide Free Shipping
$1.70 Stainless Steel 510 Drip Tip for Nipple RDA - 9mm at FastTech - Worldwide Free Shipping
Last edited:
I'm going to get a couple of those tiny tips for my Erl nano also!This what it looks like with this tiny tip
$1.70 Stainless Steel 510 Drip Tip for Nipple RDA - 9mm at FastTech - Worldwide Free Shipping
Do you need a little engineering to use steam tunner fit?
Hi, how is your wicking? I found the wicking is quiet challenging to get max flavor. To little cotton and its dryhit, to much cotton it will dryhit. For my exp the juice flow of taifun gt3 is much much better to handle 30/70 vg pg . The hussar vaping very good but for me its kinda to dry. I like vaping wet and warm. What is your exp?
So got back to my 'work' apartment, and stripped the hussar back down, and this time washed it with dish soap, and got to re-coil and re-wick with normal supplies, and it is a score 
No more metallic flavor, the 1st time I did the coil upwards, leads under the coil, this time I switched it around, so coil is a lot close to the air hole, and the flavor is really good, I have got the 2mm air insert in, and is a perfect MTL vape for me, but I do like a airy draw though, but think with the 1.3mm insert, it would work well for those who like a really tight draw too.
@rifky the wicking I have found to be easy for me, am using 70vg 30pg juice, and I just cut the cotton long enough to sit on the deck, I do not push it down, just lay it on the deck above the juice holes, and had no dry hits, I do not even thin out the cotton, just seems to work, make sure your juice control is fully open.
Picture my build and wicking, 1.5ohm clapton coil, wicked with cotton bacon and vaping at 20 watts
No more metallic flavor, the 1st time I did the coil upwards, leads under the coil, this time I switched it around, so coil is a lot close to the air hole, and the flavor is really good, I have got the 2mm air insert in, and is a perfect MTL vape for me, but I do like a airy draw though, but think with the 1.3mm insert, it would work well for those who like a really tight draw too.
@rifky the wicking I have found to be easy for me, am using 70vg 30pg juice, and I just cut the cotton long enough to sit on the deck, I do not push it down, just lay it on the deck above the juice holes, and had no dry hits, I do not even thin out the cotton, just seems to work, make sure your juice control is fully open.
Picture my build and wicking, 1.5ohm clapton coil, wicked with cotton bacon and vaping at 20 watts
So got back to my 'work' apartment, and stripped the hussar back down, and this time washed it with dish soap, and got to re-coil and re-wick with normal supplies, and it is a score
No more metallic flavor, the 1st time I did the coil upwards, leads under the coil, this time I switched it around, so coil is a lot close to the air hole, and the flavor is really good, I have got the 2mm air insert in, and is a perfect MTL vape for me, but I do like a airy draw though, but think with the 1.3mm insert, it would work well for those who like a really tight draw too.
@rifky the wicking I have found to be easy for me, am using 70vg 30pg juice, and I just cut the cotton long enough to sit on the deck, I do not push it down, just lay it on the deck above the juice holes, and had no dry hits, I do not even thin out the cotton, just seems to work, make sure your juice control is fully open.
Picture my build and wicking, 1.5ohm clapton coil, wicked with cotton bacon and vaping at 20 watts
Excellent! I'm so happy to hear you like it!
- Status
