IKV Now OPEN!

[finaritwo]

Is it just me or does my Bobas Bounty and Aztec juice and Grants Vanilla Custard completely gunk up my 801's to the point where I'm getting 1-2 days out of them at best? All three juices are 100% VG .. The first day after especially after filling is pure heaven then after the 1st refill it wears off fast....

On a more important note, I'm almost out again...I've tried many other cartomizers during the "SOLD OUT" periods,and honestly have yet to find anything comparable..Sooooo please point me in the right direction, I'll fly to the manufacturer and pick them up for you.....lol

I kinda like the gift card idea, but for me it doesn't really matter..The more I buy the more I use chasing the first fill taste. Hopefully they'll arrive soon..The wait continues.......

 

[FranC]

I'm still waiting.

 

[Big Juicy]

I am having some issues with the LR 510 mega fusion punch cartos. I am trying some thicker NET's in them, so keep that in mind. I am using a 3.7 fixed volt mecg mod with 18350 or 18500 batteries on these 2.0 cartos. Simple setup, should be no problem at all. I am getting dried, burnt hits. A couple times I thought I burnt out the carto, but no. I noticed the holes on these cartos are very small. Could it be that this juice is not getting through the holes and thus I am getting burnt, nasty, dry hits? If so, would anyone recommend I punch bigger holes in these? Any other ideas? Any help is appreciated!

 

[FranC]

You can try bigger holes but the NET's are cloggers. You'd have better luck with a clearo I think.

 

[Iken]

Is it just me or does my Bobas Bounty and Aztec juice and Grants Vanilla Custard completely gunk up my 801's to the point where I'm getting 1-2 days out of them at best? All three juices are 100% VG .. The first day after especially after filling is pure heaven then after the 1st refill it wears off fast....

On a more important note, I'm almost out again...I've tried many other cartomizers during the "SOLD OUT" periods,and honestly have yet to find anything comparable..Sooooo please point me in the right direction, I'll fly to the manufacturer and pick them up for you.....lol

I kinda like the gift card idea, but for me it doesn't really matter..The more I buy the more I use chasing the first fill taste. Hopefully they'll arrive soon..The wait continues.......

I absolutely Love AVE juice! but it does come at a price. VG is derived from coconut oil and sometimes palm oil. It's not chemically related to sugar but it does have sweeteners. It's hard to notice it because when it's heated the flavor evaporates. Though it does leave a residue. This residue engulf the coil and batting, when the unit is used, then set down, it goes through a cool down period. When this occurs, all the left over starts to stiffen up. Then when you reactivate, it just burns and destroys. Typically people who are allergic to PG are stuck with the burden of using 100% VG. Avejuice used to use PG mixtures a while back but not anymore sadly. Best solution if you want to stick with it is to order a higher mg and dilute with PG or a dash of distilled water or switch over to a clearo or evod base.

I am having some issues with the LR 510 mega fusion punch cartos. I am trying some thicker NET's in them, so keep that in mind. I am using a 3.7 fixed volt mecg mod with 18350 or 18500 batteries on these 2.0 cartos. Simple setup, should be no problem at all. I am getting dried, burnt hits. A couple times I thought I burnt out the carto, but no. I noticed the holes on these cartos are very small. Could it be that this juice is not getting through the holes and thus I am getting burnt, nasty, dry hits? If so, would anyone recommend I punch bigger holes in these? Any other ideas? Any help is appreciated!

It really can be, Frannie knows her stuff pretty well. Check the above post. Maybe you can give it a try?
I have a pretty good solution that may work. We're transitioning over from the traditional circular punch to a good size slot on both sides in an attempt to remedy thicker liquids from clogging. We're calling it the S series.

 

[Iken]

61 pages 2190 likes! I think that's a new ECF record!!

 

[Big Juicy]

I absolutely Love AVE juice! but it does come at a price. VG is derived from coconut oil and sometimes palm oil. It's not chemically related to sugar but it does have sweeteners. It's hard to notice it because when it's heated the flavor evaporates. Though it does leave a residue. This residue engulf the coil and batting, when the unit is used, then set down, it goes through a cool down period. When this occurs, all the left over starts to stiffen up. Then when you reactivate, it just burns and destroys. Typically people who are allergic to PG are stuck with the burden of using 100% VG. Avejuice used to use PG mixtures a while back but not anymore sadly. Best solution if you want to stick with it is to order a higher mg and dilute with PG or a dash of distilled water or switch over to a clearo or evod base.
It really can be, Frannie knows her stuff pretty well. Check the above post. Maybe you can give it a try?
I have a pretty good solution that may work. We're transitioning over from the traditional circular punch to a good size slot on both sides in an attempt to remedy thicker liquids from clogging. We're calling it the S series.

I use clearos and protanks and vivis and the aspire. I also use cartos now and again on certain old tanks.

When will the "S Series" be released?

 

[Katdarling]

I absolutely Love AVE juice! but it does come at a price. VG is derived from coconut oil and sometimes palm oil. It's not chemically related to sugar but it does have sweeteners. It's hard to notice it because when it's heated the flavor evaporates. Though it does leave a residue. This residue engulf the coil and batting, when the unit is used, then set down, it goes through a cool down period. When this occurs, all the left over starts to stiffen up. Then when you reactivate, it just burns and destroys. Typically people who are allergic to PG are stuck with the burden of using 100% VG. Avejuice used to use PG mixtures a while back but not anymore sadly. Best solution if you want to stick with it is to order a higher mg and dilute with PG or a dash of distilled water or switch over to a clearo or evod base.
It really can be, Frannie knows her stuff pretty well. Check the above post. Maybe you can give it a try?
I have a pretty good solution that may work. We're transitioning over from the traditional circular punch to a good size slot on both sides in an attempt to remedy thicker liquids from clogging. We're calling it the S series.

 

[Bovinia]

Just dropping a drive by hug on everyone

 

[Iken]

I use clearos and protanks and vivis and the aspire. I also use cartos now and again on certain old tanks.

When will the "S Series" be released?

Very cool! They are on the production line and should be here by months end senior Juicy

Love it! I'll have done pics put together for you soon

Just dropping a drive by hug on everyone

BIG ones right back to you sweetheart!

 

[FranC]

Can't wait to try the s series. Sounds great.

 

[5cardstud]

My brand new, Well pretty new anyway, Auto Ego quit on me.

I'm so sad. It won't charge either. Oh well, Que Sera Sera.

 

[FranC]

That's a bummer 5c.

 

[finaritwo]

Thanks Iken, Explanation was informative...I've tried three punches sometimes on my 801's but it's a hit or miss sometimes. It either gives me great wicking or instant flooding with no return...

To the main and pestering question: " Are the 801 Fusions on the horizon?.....I know the answer , but it just makes me feel better to ask and think it will make them get here quicker...lol

 

[sgenn99]

The waiting is the hardest part...once you're hooked on the good stuff...you're ruined.
Lesson learned: buy at leaat 1 box extra box..

 

[FranC]

Just passing thru to say "I'm still waiting".

 

[5cardstud]

That's a bummer 5c.

Thanks Fran. It is a bummer but I'll get over it. I'll put one on my next order. I just got one yesterday for my son.

 

[Iken]

My brand new, Well pretty new anyway, Auto Ego quit on me.

I'm so sad. It won't charge either. Oh well, Que Sera Sera.

Oh no! Was that one of the original stainless sets?

Thanks Iken, Explanation was informative...I've tried three punches sometimes on my 801's but it's a hit or miss sometimes. It either gives me great wicking or instant flooding with no return...

To the main and pestering question: " Are the 801 Fusions on the horizon?.....I know the answer , but it just makes me feel better to ask and think it will make them get here quicker...lol

Your very welcome! My emails are more killer Are you doing the punches yourself? Try aiming about a qauter inch from the top of the fitting. 10mm would be better, but 1/4 is close enough. You want to get around 3mm in diameter at the least. Then take a needle point to the batting in your newly created holes and loosen up the batting a bit. When your not wicking properly, just grasp where the tank meets the device and give it a good dry pull. You should see some bubbles rising and you'll be in the clear.

Totally understand about the golden question and thank you so much for hanging on for me. It will be totally worth it. We got the standard size 510 Fusion models coming in on the same batch and with moving forward with the S series that will leave the circular punch in the past, we're looking at some time, but not long. We should be good to go with a bountiful stock this month.

Just passing thru to say "I'm still waiting".

And I love you for it!

 

[Bovinia]

I usually get the standard length SR Fusions and punch them myself, but even with the Fusion Punch series I punch an extra hole in between the pre punches. My ADV is naturally sweet, so I understand the wicking problem When I refill my tank, I also run a slim needle down thru the center tube to clear any build up. Doing this, I usually get a week or so out of a Fusion.

 

[5cardstud]

Oh no! Was that one of the original stainless sets?
Your very welcome! My emails are more killer Are you doing the punches yourself? Try aiming about a qauter inch from the top of the fitting. 10mm would be better, but 1/4 is close enough. You want to get around 3mm in diameter at the least. Then take a needle point to the batting in your newly created holes and loosen up the batting a bit. When your not wicking properly, just grasp where the tank meets the device and give it a good dry pull. You should see some bubbles rising and you'll be in the clear.

Totally understand about the golden question and thank you so much for hanging on for me. It will be totally worth it. We got the standard size 510 Fusion models coming in on the same batch and with moving forward with the S series that will leave the circular punch in the past, we're looking at some time, but not long. We should be good to go with a bountiful stock this month.

And I love you for it!

No it was my green one.