Introducing the Precise Strata RDA
- Thread starter forcedfuel50
- Start date
- th_trl_thread_readers 0
- Status
Is it safe to assume the P+ version will have a nice Satin finish?
Oversight, we'll get it changed on the site for the option of polished or satin, for now, make a note in the comments section of your order. If you already ordered, shoot me an email if you want the satin (by default it comes polished, so no need to specify if you wanted polished).
It's the butter on my bread.
Any satiny options? Not 100% if I would want satin anyway, but just in case.
EDIT: Nevermind
How about satin extension tubes? I can't get a a fully satin look anyway.
Any satiny options? Not 100% if I would want satin anyway, but just in case.
EDIT: Nevermind
How about satin extension tubes? I can't get a a fully satin look anyway.
Last edited:
Excellent....just pre-ordered for my ELAs and P+!!!! This has made my day.
Yes, i'll take some for you. I set one up with quad coils too, but keep in mind, my coils will never be as pretty as yours
yes please do
Yes, but the exterior and interior design will remain identical and the only changes that can be realistically made (and may or may not be made depending on the testers feedback) is:
-Short or long Helix machined airfoil (testers will be getting both the short and long version)
-Air holes size (we have room to go up a drill size or two if necessary)
-Also, the center post where the top of your coil will wrap around sits .100 higher then the two outer grounds but we've also already machined some ones that are even with the two outer grounds. We raised it a bit so that the coils rise up away a bit from the packing, but if shorter ones are needed, we have them. (I think its a non factor, but just in case).
Last edited:
very cool.. coil wraps around the center post for the positive connection.. its not like a traditional atty where theres 2 nuts that the coil gets tightened in between them?
$
):^}*}*{!{|]<¥+}=:$!!!!!!!! I own all 3 of the mods. My wallet can handle no more!!!!
Bumping this since there were concerns about airflow:
Heres an example of the relatively small size of the Precise Strata's Chamber. You'd think the smallest one on the right would have the smallest chamber but:
Chamber Volume in CC (base protrusion into the rba's taken into account) :
Left : 3cc
Middle (Strata): 1cc
Right : 1cc
View of the chambers:
Next up you see the air holes, the Precise Strata flows up to four times as much air as these examples and is adjustable all the way down to no airflow. Airflow volume should not be an issue on the Strata:
Heres an example of the relatively small size of the Precise Strata's Chamber. You'd think the smallest one on the right would have the smallest chamber but:
Chamber Volume in CC (base protrusion into the rba's taken into account) :
Left : 3cc
Middle (Strata): 1cc
Right : 1cc
View of the chambers:
Next up you see the air holes, the Precise Strata flows up to four times as much air as these examples and is adjustable all the way down to no airflow. Airflow volume should not be an issue on the Strata:
Internal brain fighting has began...
A satin to go along with my satin Ti tube or a 2nd polished one?
HEEEEEEEEEEELP!!!!!!!!!!
A satin to go along with my satin Ti tube or a 2nd polished one?
HEEEEEEEEEEELP!!!!!!!!!!
Done. P+ version in Satin.
You can't see it, but I'm doing a little happy dance in my head at the moment.
I guess I should hold back on the speculative comments, and just wait until I have one in hand.
My guess is it will be something along the lines of ".........." (speechless)
My guess is it will be something along the lines of ".........." (speechless)
ELA version pre-ordered Preparing to enter stalking mode for the Simplicity version's release
Preparing to enter stalking mode for the Simplicity version's releaseI don't see the ELA Strata preorder lasting long. With around 500 ELAs being sold and only 200 Strata for preorder...these should be gone in a heartbeat. In other words, buy now and think later!!!!
I don't see any of the versions lasting long..
I can't decide!!!
The polished will def sit atop my polished Ti but I also have a satin Ti tube that for the moment is using a reg Simplicity top cap and bottom button.
Score another polished for the satin Ti setup or satin for the satin???
My brain hurts, I can't decide...
Preordered. Woohoo!!!! Still waiting on my ELA (161xx), hoping that they ship at the same time *fingers crossed* Probably shouldn't have done it, but I just got paid so I did it anyway. Derp.
sent from a monstrous screen with an itty bitty keyboard
- Status
Similar threads
- Locked
- Locked
- Locked
