Introducing the Precise Strata RDA
- Thread starter forcedfuel50
- Start date
- th_trl_thread_readers 0
- Status
Try 2 thick .100 orings (.200 total) in the bottom of the battery chamber and 5 washers on the included brass post (you'll find it in your parts kit). I think that should be the setup for the P+. May have to experiment a bit with orings, maybe one thick (.100) and two thin (.070 x 2) for a total of .240.
Would they be in the parts kit for the p+ or for the strata? Because I just got the strata second hand with nothing but a drip tip o ring 
Would they be in the parts kit for the p+ or for the strata? Because I just got the strata second hand with nothing but a drip tip o ring
Shoot me an email to supertmanufacturing@yahoo.com with your device name and address and we'll get you taken care of!
O.K.. Here is an update...
Still.. Envision.. Crazy woman.. Naked.. Kitchen.. Cats..
I still am not ready to go 'out of the box'. Hey, it's hard to teach an old cat new tricks! So..
My build yesterday was not bad. But, I wanted some more clouds. Today, I did dual coil, horizontal mount, rolled cotton. I wanted a .5 ohm build. Normally, I use .24 gauge Kanthal. There is no way to do a .5 ohm build, with .24 Kanthal, and mount horizontal with my size coils. There is not enough room for that many wraps. So, I found a small piece of .26 gauge Kanthal around. There was enough to achieve a .6 ohm build.
Second try, and pretty darn good. Taste: Wow. My coffee never tasted so good. Clouds: Today, I have more clouds. The volume of cloud is not as great as what I am used to. But, the clouds are more dense/thick than what I am used to. Kinda nice. Throat Hit: It hits. I still wish I had some lower nic on hand to try out.
So, again, I did not go 'out of the box'. I stepped it up to a dual coil. And, the result is pretty darn good.
BTW: I did the dual coil with a continuous piece of wire. This was my first dual. I figured it would be hard to attach two. I took the positive post out, attached the wire to the center post with a loop, and then wrapped my coils out from the post. Then, I just had to insert the post and attach the end of the coils to the negative posts. Hey, maybe everybody does that? I don't know. I am a 'lone vaper' here. And, I rarely watch vids. Unless, somebody hot, or somebody I know, is starring in them.
I'm going to sit back and enjoy this for a while. I hope everyone is having a good night!
Still vaping this build. Taste! Taste! Taste!
Did you find that lost Strata center pin and drip tip? Maybe David can send you those? Would not think they would be that costly..........
No, I did not find them.
I am sure, eventually, they will be available for purchase.
My Stratas have me completely spoiled. It has been over a month and I haven't touched anything else. Have a Heron sitting there that hasn't gotten a stitch of love.Still vaping this build. Taste! Taste! Taste!
My P+ build is my favorite, can't remember what it was I'll have to look back. My ELA one is the one I've been using lately though, went to work with me daily last week. The Simplicity is the one I'm using for experiments.
It is a great atomizer! The draw is so unique! The vapor, the taste, the magnificent throat hit! After putting it through its daily paces as my #1 I give it an A-. The minus comes from the fact that it can leak. If I remember to close the air off when I throw it in my pocket upside down or lay it down for the night it isn't an issue, but that's hard to do. Maybe it's a pipe dream to wish for a totally leakless dripping atomizer, though that's one area where my builds could mitigate it if I put my mind to it. I just like the simplicity and ease of cleaning with only silica wick tails hanging into the bare well.
1) Click 'reply With Quote'. 2) Type post.
Keep practicing those computer skills.
I just figured that out. I am such a tardo!!
Man! I am getting a serious nic buzz tonight off of the strata.
I have been on a three day nic buzz.
- Status
Similar threads
- Locked
- Locked
- Locked
