Kaiser Atomizer

[Budkiss]

I had a hard time the first time i built this tank. The lead feed through the cup and into those tiny post holes was a challenge. It took a few tries to get the frankenstein screws to hold my 28 gauge wire. I broke the little center "tip" in the sides of the ceramic cup on first build but it doesn't seem to affect vape. The air control ring is a bit loose. I like the juice control option. I actually think the vape on this is better than the yiloong fogger 4.4 (i have both)

Has anyone done a dual coil on this? Want to share your experience?
Was it better than the single coil build. If so, what size wire, diameter coil, wraps and ohms?

 

[brianc11111]

what ive got now is 26ga 5/64id .37 ohm duals. vape is great!
definately have the juice control screwed pretty far out.
ive thought of using 3/32id but im really liking the current build.

 

[350ZMO]

The air control ring is a bit loose.

Mine is tight thanks to the o-ring, now the foggers I have are loose as a goose.

 

[Tinkiegrrl]

I think I hate this thing. Getting a single coil mounted on it took me FOREVER last night. Then, filling it without leak all over was a pain in the you know what. Vapes okay, but not good enough for the trouble I think. I can't imagine how I'm going to do a dual coil in it. I think I need two blunt needle tips maybe...

 

[brianc11111]

I think I hate this thing. Getting a single coil mounted on it took me FOREVER last night. Then, filling it without leak all over was a pain in the you know what. Vapes okay, but not good enough for the trouble I think. I can't imagine how I'm going to do a dual coil in it. I think I need two blunt needle tips maybe...

for duals, i took both coils still on their drillbits, put the drillbits in a vise and with pliers twisted the legs together to make one wire.
makes it a lot easier to mount. the largest wire size ive installed is dual 26ga, but i think i could go bigger.
i did a single 22ga and it worked good. dont think dual 22ga would work at all.

ive never had a leaking issue at all. and i dont close the air intakes or anything.
what are you using to fill with?
i use a needle bottle so the air in the tank can escape when filling.
hope this helps

 

[Tinkiegrrl]

for duals, i took both coils still on their drillbits, put the drillbits in a vise and with pliers twisted the legs together to make one wire.
makes it a lot easier to mount. the largest wire size ive installed is dual 26ga, but i think i could go bigger.
i did a single 22ga and it worked good. dont think dual 22ga would work at all.

ive never had a leaking issue at all. and i dont close the air intakes or anything.
what are you using to fill with?
i use a needle bottle so the air in the tank can escape when filling.
hope this helps

Needle bottle, like you. I just refilled it, and wound up with a horrendous gurgle and lost half my tank of liquid blowing it out. I think my mistake was making my usual 1/16 sized microcoil. It must not allow for enough wicking. When I get home, I'm going to add another layer of cotton on top I think.

 

[brianc11111]

i believe youre correct tinkie. after i posted and left i thought about how much wick you had in it.
i usually like the bigger diameter coils so didnt think of micro's.
on this one i do 5/64id on the duals and on singles 3/32 or 1/8th

 

[Valld]

Could somebody of the happy owners please measure (in mm) the height, diameter and thickness of the pirex tank? I ordered the atomizer and I would like to have a spare glass tank. Thanks in advance!

 

[Kemosabe]

 

[350ZMO]

Could somebody of the happy owners please measure (in mm) the height, diameter and thickness of the pirex tank? I ordered the atomizer and I would like to have a spare glass tank. Thanks in advance!

Well I'll tell ya I am still vaping my original donut build almost exclusively and it will be 3 weeks this Thursday. I have enjoyed it so much that I didn't want to take it apart to measure it and decided I needed to buy a spare. All I have been doing is filling it and vaping it. Even on the BIG fogger I was rebuilding it once a week like clock work. This thing flows juice so well I am impressed. All my foggers are now collecting dust. Can't wait for the BIG Kaiser.

The pyrex tank is 15mm long and the same diameter and thickness as the fogger tank which is much longer. I measure the diameter of the tanks to be 21mm. I do not have my micrometer with me so I can't tell you thickness or decimals of a mm. The later I doubt is important anyways. But the thickness appears to me to be the same as the fogger. I'm going to guess somewhere shy of 2mm probably 1.5 but I am not sure on that.

 

[Valld]

Thanks 350ZMO! It looks like the pyrex tank for Kayfun nano kit from Fasttech may fit, I will report ones I receive everything.

Sent from my SM-G900H using Tapatalk

 

[Tinkiegrrl]

Anyone know where I can get a replacement ceramic cup for this? I broke the prongs on mine. It doesn't affect the vapor it seems, but it's currently stuck in the atomizer, and I'll likely need to break it all the way to get it out. Managed to get a build in there anyway, but I'm sure I'll want to clean under it soon...

 

[350ZMO]

You could ask the vendor you bought it from. I would try warm water to flush it out, different rates of thermal expansion between the SS and ceramic, it should come right out.

 

[Tinkiegrrl]

You could ask the vendor you bought it from. I would try warm water to flush it out, different rates of thermal expansion between the SS and ceramic, it should come right out.

Tried it. Didn't work... I can still build on it. They really should make them available for purchase seperately. I like it with a dual coil in it, but I don't like it enough to buy another when the ceramic completely breaks. Do you think a Rose ceramic cup would fit?

 

[350ZMO]

Tried it. Didn't work... I can still build on it. They really should make them available for purchase seperately. I like it with a dual coil in it, but I don't like it enough to buy another when the ceramic completely breaks. Do you think a Rose ceramic cup would fit?

I do not know.

 

[WharfRat1976]

Another Asian POS. Imho..

 

[brianc11111]

do you have one to be even remotely be qualified to make that statement?
i have this feeling that you dont, and that also you dont have a clue of what you are talking about.
its kinda like....I have been to Austin, scuba dived there a lot. but im not qualified to really say how the city is.
i could go by my opinion that its a liberal overpriced college town and really is a disgrace to texas.
but that would just be an uninformed opinion now wouldnt it?

 

[VapDrak]

Anyone know where I can get a replacement ceramic cup for this? I broke the prongs on mine. It doesn't affect the vapor it seems, but it's currently stuck in the atomizer, and I'll likely need to break it all the way to get it out. Managed to get a build in there anyway, but I'm sure I'll want to clean under it soon...

You can find them here:

Kaiser Selbstwickelverdampfer  -  kaufen im Onlineshop smart24.net

I'm under the impression that these guys had it first, kind of the "Russian" RBA... a (Rose in this case) clone under german QC.

 

[350ZMO]

How is everyone getting along with their Kaiser?

Both of mine are flowing juice like crazy with the juice slots being above deck level as opposed to below as in most all the other RTAs like Fogger V4, etc. I really like this as it keeps the vape very wet, saturated, cool and condensed. Just replaced the Rayon on my original so that's a month without having to mess with it.

 

[caged]

Is there any place that sells a reasonable priced pyrex tank?