Right? I just hope they still have some in stock tomorrow morning.
- Status
Right? I just hope they still have some in stock tomorrow morning.
In most cases the bottle neck is US postal Customs, unless ordering from Russia then both are lengthy.
I made one order with SlowTech (never again). Their problem is most of their stuff goes through Hong Kong where they sit on it and inspect everything for contraband. I don' think SlowTech stocks anything. They get an order and they just pass it on to the Chinese makers who ship direct from their factory. Hence, the Hong Kong bottleneck. Just my guess.
I agree but never thought about it that way as in they don't stock anything. I've ordered from cloud9 and Atmomixani and both times came in within a week. I don't mind ordering from Europe but I'd rather buy from stateside.
My flavor experience is definitely not muted Turbo, and for me, this setup is better in all areas
not really sure how additional wicks/liquid on the coil would mute flavor
but hey, if it didn't work for ya, it didn't work for ya. Like i said earlier
the 2 biggest differences are much thicker vapor and flavor holding up through at least tankfuls. Here's another shot of what i described earlier with the loop gap.
The supplied drip tip was a bit long for me as well…picked up these 2 at Kidney Puncher…6 bucks each and a real nice match. 13mm from above 0ring to the tip…
Now THAT's what I'm talkin about! Both of those look perfect for the KFL. The first thing I did was yank off the standard pogo stick drip tip that comes on them and have been using an old chrome shorty that looks like the curved one in your pic's. I like the size but have always hated the chrome look of it on the KFL. Time to order more vape gear.
I'm glad you mentioned the GP tips don't fit right. I almost ordered the Classic one when I first bought my KFL+. I love the looks of those but not if I have to hack it down to make it work.
Truman - That set-up looks interesting but doesn't that set-up restrict the air flow and make for a tighter draw? Might have to try this one out on my next "wick-up". Are you using a cotton ball or yarn?
Strange. I own both GP tips and there is the SLIGHTEST gap on top of my KFL. It definitely fits just not all the way down.
Woody - I think you should send me your classy one and let me verify this to be true.
Those are sweet lookin tips.
Haha. I'm too in love with anything GP. I will never get rid of them.
Do you have trouble with your Paps keeping the bottom cap and battery tight after you screw on and off your KFL? I have adjusted the center pin connection to it's lowest max and pushed the battery connection up as far as I can but every time I take the KFL off or take the bottom cap off to change the batt one or the other always loosens up. It's not a huge deal but it gets a little annoying.
Hmmm I'm trying to picture what you are talking about. I don't believe I have that problem. Which mod do you own? What batteries do you use?
Same mod as you have. Paps V2.5 SS using AW IMR 18350's
Well for one, the bottom cap cannot be adjusted for battery configuration. Make sure the screw making the contact on the negative end, which is reverse threaded, is JUST protruding over the nut holding it on. A mm is enough. Also the mod comes with TWO pins for the positive post. You can try swapping it with the other one. Also look at the Delrin cap on inside of switch and make sure it's sitting properly. One of those should help. If not, stop by the GP thread and even PM Perseas, the creator. He is on there a few times daily. We are a great group over there and I guarantee if I cannot help you, someone will!
Yep, I've checked all those things and the other pin that came with it is for the 18500 configuration from what I understand. I think I'll post the question over there. Just haven't bothered to until now cause it's not that big of a deal. I was just curious if you had the same issue. Thanks!
It almost sounds like things are TOO tight on yours. Definitely get ahold of Perseas and he will sort you out. One if the benefits of owning a GP is the service! We would love to have you on our thread as well.
Love my PAPs!!! never any issues. I run Stratus22, KLites & soon a SQuape on it. Xmass should get me a PAPSX. There are different top cap adjustment pins, i beleive there were 3 different versions made.
I had to change to the thinner post in the extras bag to have my 18350 be able to tighten down correctly...
Sent from my iPad
Right. I use the thinner post for 18350 and 18650 (MNKE) with my KFL. my AW 18650 seems to work fine with the thicker post. But the thicker post is definitely needed for my AW 18490s.
Consider yourself lucky you live in the States. I have to wait ten to for teen days for all my orders, even the ones from China.
- Status
Similar threads
