- Status
Just ordered my 1st "Russian 91%"... my *6th Kayfunish RBA
_____________________________________________
*KFL x3, Kayfun 3.1ES x 1, The Russian 100% x1
I now have 2 kayfun lites, a kayfun lite+ and a Russian 91%. I like the R91% as much as I do the kfls. I'm not super crazy about the finish but it does tend to make it different and it looks good on the Kurgan provari. Where did you order from?
I've actually got an extra kfl+ here that I ordered for someone and of course I had to get it cleaned up and make sure it works before I give it to him LOL. Seriously though, it's for a semi-new vapor.. His Mother had me order it for him for Christmas (I also helped her order him a provari) So now I've got the fun job of teaching him to build, wick and maintain it (I'm not being sarcastic.. I can't wait to show him what to do
) He's 18 btw and his parents want him to quit smoking.. he's been using the itaste vv3 and is enthusiastic about vaping. I normally wouldn't use someone else's stuff but it took several washings to get the machine oil taste out of it so I couldn't just take it out of the box and say "here"
Last edited:
Is that the yarn from walmart or is their's labeled "peaches and cream" ?
Wal-Mart carries peaches and cream.. some other stores carry sugar and cream.
I'm still getting issues. I haven't had time to sit down and fully troubleshoot it, so I just tried all recommendations. Luckily, I have a slow day at work tomorrow, so I can try to figure out what I'm doing wrong. I'm going to be around a vacuum pump, so does anybody know the actual pressure (-) needed for the tank to function?lol
Edit:I've been using a syringe, about 30 seconds or so to fill 3mL.
I'm still getting issues. I haven't had time to sit down and fully troubleshoot it, so I just tried all recommendations. Luckily, I have a slow day at work tomorrow, so I can try to figure out what I'm doing wrong. I'm going to be around a vacuum pump, so does anybody know the actual pressure (-) needed for the tank to function?lol
Edit:I've been using a syringe, about 30 seconds or so to fill 3mL.
Last edited:
I now have 2 kayfun lites, a kayfun lite+ and a Russian 91%. I like the R91% as much as I do the kfls. I'm not super crazy about the finish but it does tend to make it different and it looks good on the Kurgan provari. Where did you order from?
I've actually got an extra kfl+ here that I ordered for someone and of course I had to get it cleaned up and make sure it works before I give it to him LOL. Seriously though, it's for a semi-new vapor.. His Mother had me order it for him for Christmas (I also helped her order him a provari) So now I've got the fun job of teaching him to build, wick and maintain it (I'm not being sarcastic.. I can't wait to show him what to do
I normally wouldn't use someone else's stuff but it took several washings to get the machine oil taste out of it so I couldn't just take it out of the box and say "here"
Professor Donna eh? But seriously, Kayfuns are the best & easiest RBAs one can get for a noob indeed. You are doing a yeoman service assisting him.
I fetched mine from ECV, here in Canada. $100 Shipped... also reaches me in 2-3 days√
I've been rewicking using cotton every 1-2 days each, flavour is spot on everytime.The key is in ur guesstimates(lol). It has to be fluffy and do take note not to compress(?) the cotton too much. Only the part where it has to be threaded in, then fluff it up again. The cotton also has to move to and fro with slight resistance cuz we all know it expands when juice is present. Hope it helps!
Just ordered my 1st "Russian 91%"... my *6th Kayfunish RBA
_____________________________________________
*KFL x3, Kayfun 3.1ES x 1, The Russian 100% x1
I like my KLites, over the russian 91%... I have only had it a month, it might grow on me... but the finish does bother me. OCD here. Love my mod'd v2 Fogger much more then the R91
K..too impatient to wait or use a dripper. I tried just taking a couple of syringe pulls of air out. Seems to be working, I didn't think it would before. The syringe has such a loose fit, and I assumed it would equalize immediately. Hopefully, I won't be surprised to find a tank emptied out in the morning. If it's leaked on me before, I usually see the airhole fill up with liquid after a pull or two.
Thanks for the help from everyone.
Thanks for the help from everyone.
Does anyone know where i could find a kayfun lite? i dont want the plus because it looks like the screw would interfere with me drilling my air hole slightly larger. i have a lite currently but i keep having to share it with my girlfriend and im ready to spend another 100 bucks to get out of it. also i dropped mine for the first time and now it has scratches so its time to give it away. if anyone knows anything that would be awesome, thanks! im watching one ebay but it has no buy it now price, hate that....
Well I just took a dremel to the juice channels in my KFL+. Enlarged them just a smidge and re-wicked with a bit more cotton than I was using before and lo and behold I'm getting much fuller and saturated vapes at 15watts! YAY!!
I used one of the bits in my diamond dust covered grinding bit kit. One that was cylinder shaped and fit right inside the channels. I also re-did my air control screw, grinded down the spare screw (the first one I messed up the seal by hurting the threads) and I can actually control the air/juice flow much better now. Finally can say that I love my KFL+!!
I used one of the bits in my diamond dust covered grinding bit kit. One that was cylinder shaped and fit right inside the channels. I also re-did my air control screw, grinded down the spare screw (the first one I messed up the seal by hurting the threads) and I can actually control the air/juice flow much better now. Finally can say that I love my KFL+!!
I'm also looking for a non plus kfl
-Sent from outer space using DNA20 and Kayfun Lite
Get a 1/16th drill bit and some sugar and cream cotton yarn. Boil the yarn for 10 mins, rinse in cold water, boil 20 more, rinse again. Let it dry over night. Wrap a 10 wrap 28gauge wire micro on the bit. Take a few inches of yarn, cut one of the tiny strings that make up the yarn and remove it from your strand and discard it. Take the yarn that's left over and thread it through the coil. Loop each side down to the deck and back up, trim the yarn so no extra goes past the coil. Make sure the loop going down to the deck has a gap in it for air to get below the coil. Make sure the loops go just to the channels, not blocking them. Thats it, should look like this and you will be in kayfun heaven.
-Sent from outer space using DNA20 and Kayfun Lite
Had a scare this morning before leaving for work. Dropped a KFL on a Neme clone onto ceramic tile. Luckily it fell near horizontally. I now have a badge of honor scuff on the top cap of the KFL. But the bad part was the plastic tank skewed a bit. I could see the o-ring at the bottom connection to the SS wall. I tried to unscrew them, but they were essentially thread locked. The bad thing is that this was an airpath, and I could hear "glug glug glug". So juice was just weeping out of the air hole.
So I figured, just try to snap them back together. Put on the countertop, covered with a rag and pressed down hard. Heard a single snap, looked and saw less o-ring. Repeated and heard another snap, o-ring gone. I unscrewed it all and reassembled and she's all good again.
Thankful that this happened on my Neme clone, as there's now a scuff on the button. If this had been on my authentic Neme, I'd have been heartbroken. Also, thankful I have 2 KFLs and 1 KFL+. This scuffed one is now the beater. LOL.
So I figured, just try to snap them back together. Put on the countertop, covered with a rag and pressed down hard. Heard a single snap, looked and saw less o-ring. Repeated and heard another snap, o-ring gone. I unscrewed it all and reassembled and she's all good again.
Thankful that this happened on my Neme clone, as there's now a scuff on the button. If this had been on my authentic Neme, I'd have been heartbroken. Also, thankful I have 2 KFLs and 1 KFL+. This scuffed one is now the beater. LOL.
We have had several reports of the same thing. Seems those plastic segments heal themselves.
Just received my second KFL+, this time from InTaste.de and the service was amazing. Shipped on Monday and delivered today - I didn't even have time to get impatient 
No machine oil smell from this one but it's getting a good soak anyway. The drip tip is super tight with no wiggle at all. It appears SvoёMesto is listening.
I'm rockin' the first one in 10ml mode and shouldn't have to touch it for at least 3 days, except to vape of course
With the large clear tank on the bottom you can see right down to empty. 1.3ohm coil at 3.1 volts - it just doesn't get any better than that 
No machine oil smell from this one but it's getting a good soak anyway. The drip tip is super tight with no wiggle at all. It appears SvoёMesto is listening.
I'm rockin' the first one in 10ml mode and shouldn't have to touch it for at least 3 days, except to vape of course
With the large clear tank on the bottom you can see right down to empty. 1.3ohm coil at 3.1 volts - it just doesn't get any better than that 
Just received my second KFL+, this time from InTaste.de and the service was amazing. Shipped on Monday and delivered today - I didn't even have time to get impatient
No machine oil smell from this one but it's getting a good soak anyway. The drip tip is super tight with no wiggle at all. It appears SvoёMesto is listening.
I'm rockin' the first one in 10ml mode and shouldn't have to touch it for at least 3 days, except to vape of course
I'd like to see a pic of that bad boy...
Sent from my iPad
Had my kfl+ for a week now, love the flavor from this thing!
Using a wide,Truflow drip tip & chimney coil @ 1.3 (3.7v) to open up the airflow a bit beyond what the bottom screw delivers. Great for tobacco, creamy & desert juices, but I still prefer the Kayfun tip or another thinner drip tip for fruits.
I may need a 2nd one...
Sent from my iPhone using Tapatalk
- Status
Similar threads
