Kayfun LITE

[pokerplayer]

Put the Dremel to 1 of my K-Lites.


As arrived out of box on a Poldi:

After 20 minutes with Dremel, buffing pads and red polishing compound:

I like it mo betta!

 

[9ball_AJ]

Put the Dremel to 1 of my K-Lites.


As arrived out of box on a Poldi:

After 20 minutes with Dremel, buffing pads and red polishing compound:

I like it mo betta!

Looks great!

 

[Ryd1ZZ]

I’m pretty sure this has been asked before, but I’m not sure where to look. How does the K-Lite perform with high VG juice 70+%???

Thanks!

I've had some trouble with it. Indigo Cpt. Ron is a 50/50, and probably the thickest juice I have right now (seems thicker than 50/50). It works, but I have to give it a couple of quick pulls (no power) to get more juice to the wicks. This is especially true with a fresh battery.

Setup is .9ohm diagonal coil, 28 gauge kanthal, 2mm ekowool. Built it like Todd shows in the reviews.

Going to try higher resistance and figure 8 method next, and see if it improves.

 

[Ryd1ZZ]

Only went back a couple pages, so not sure if this has been discussed. Is anyone else getting some slight leaking from the fill area? Every time I take it off the mod, there is a bit of juice between the mod and the k-lite. I have 2 and they both do this.

 

[9ball_AJ]

Only went back a couple pages, so not sure if this has been discussed. Is anyone else getting some slight leaking from the fill area? Every time I take it off the mod, there is a bit of juice between the mod and the k-lite. I have 2 and they both do this.

Put a small amount of teflon tape on the fill screw. This has fixed my issue and lasted for about 4-5 tank fulls so far without a drop.

 

[qorax]

Only went back a couple pages, so not sure if this has been discussed. Is anyone else getting some slight leaking from the fill area? Every time I take it off the mod, there is a bit of juice between the mod and the k-lite. I have 2 and they both do this.

Sure it is not 'weeping', thru the air-hole instead? There r a few here who have leaking issues from the fill-hole... and some plugged it with a bit of teflon, while the others used the small O-rings of the 'green mini-screwdriver' (which came in the package).

I personally have no leaking from anywhere, though I 'only' use the fill-hole for topping up, which is nearly once-a-day... since the last 15 days!

 

[Ryd1ZZ]

Put a small amount of teflon tape on the fill screw. This has fixed my issue and lasted for about 4-5 tank fulls so far without a drop.

Awesome, thanks! I was thinking this or a tiny o-ring. Just wanted to make sure I wasn't the only one

Besides the slight leak, these things are great.

 

[Ryd1ZZ]

Sure it is not 'weeping', thru the air-hole instead? There r a few here who have leaking issues from the fill-hole... and some plugged it with a bit of teflon, while the others used the small O-rings of the 'green mini-screwdriver' (which came in the package).

I personally have no leaking from anywhere, though I 'only' use the fill-hole for topping up, which is nearly once-a-day... since the last 15 days!

I'm sure it's not the air hole. If it is, it's being very sneaky about it lol. I never get any gurgle like I would expect if some liquid made it into the air hole. Don't see any around that area either. I'm going to try the tape or o-ring (if I can find one), and I think it will stop. I didn't get a screwdriver with mine Which vendor sends them? I got mine both from Cloud 9.

 

[manji1]

Has anyone else set theirs up with ribbon wire? I've done 28g and 30g 10 wrap micro coils, 28 and 30 3/4 and 4/5 standard sized coils, and tonight I set it up with ribbon. I did a 3/4 of .7 ribbon around a 3/32 drill bit and am using cotton yarn for wick. All I have to say is wow. I use ribbon in my gennies but not in my drippers because I feel it vapes too warm in those, but in the Lite it's perfect.

 

[shroom]

Alright, I can show my picture too.

 

[qorax]

Alright, I can show my picture too.

Ou - wow - Wou! U got a B&M or something? Love that collection, man

 

[qorax]

I'm sure it's not the air hole. If it is, it's being very sneaky about it lol. I never get any gurgle like I would expect if some liquid made it into the air hole. Don't see any around that area either. I'm going to try the tape or o-ring (if I can find one), and I think it will stop. I didn't get a screwdriver with mine Which vendor sends them? I got mine both from Cloud 9.

This is how most of us received ours:

There was a green mini-screwdriver in the package. Came from InTaste

 

[Innocuous]

$0.85 at Fasttech.

 

[Chuckq4yoo]

I thought when I ordered from vaperev they were gonna include the screwdriver too :/

 

[liveone]

Thought I was going to have my KFL waiting for me at home since tracking said at Los Angeles sort center last I checked and my brother got his down at the beach.

Nope.

It's now at Richmond, CA sort center. Someone tell USPS that they can't pad the meter like taxi drivers. It just doesn't work.

 

[shroom]

Ou - wow - Wou! U got a B&M or something? Love that collection, man

Thanks a lot Qorax.
I don't have any B&Ms or anything like that I'm just another small trader. Everything is for myself, I think. A little overdone it, thought.

 

[shroom]

This is how most of us received ours:

There was a green mini-screwdriver in the package. Came from InTaste

BTW. Did you order the gold drip tip separately or it was included with the K-Lite? I also, have got mine ones from Intaste and I don't have any in my package.

 

[Chuckq4yoo]

If you ordered from vaperev and located in SoCal, I don't know understand why their shipments take longer than 2 days. I just happened to order juice online from their site, expecting it to arrive the next day... nope. Didnt get it for a week.

 

[qorax]

$0.85 at Fasttech.

So very true
_______________________________________________
*Nonetheless, nice touch by InTaste, isn't it?

 

[qorax]

BTW. Did you order the gold drip tip separately or it was included with the K-Lite? I also, have got mine ones from Intaste and I don't have any in my package.

*LOL*, but they actually gave it to me for FREE. Man, I love InTaste