- Status
I know. I have about 20 Genesis Atomizers built with SS Mash, SS Rope and combination of both utilizing NR-R-NR method and Flat Ribbon A1 Kanthal.
Let me clarify something here: I'm a truck driver, but not newbie vaper.
In fact here is a snap shot of my truck dash board. Taken with an iPhone couple of months ago.
I have to say...that is frigging awesome....what a collection and in your means of making a living to boot...
You obviously haven't driven dual clutch automatic transmission...
Got ya on the blockage. On the first kayfun I used a 5/64, which worked really good. Just break down the coil first, then remove the 510 post and positive block. Also if you have an adjustable airflow screw, remove that. Then just drill main airhole till you reach 510 channel. This is what I did on my authentic. My next kayfun I did, I went to 3/32 which didn't seem any difference. Start with 5/64, that should do ya. I don't own a clone so I'm not sure if all things will be the same but the kayfun is definitely better with this modification. If you have a press then I'm sure you have some really good bits because that's what you need. Also give it a good wash, then reassemble.
Actually I have, and I find them just as boring as any other automatic. I've also seen how much they cost to fix when they break.
No, I haven't. Looks as over-complicated as a DCT.
Actually I have, and I find them just as boring as any other automatic. I've also seen how much they cost to fix when they break.
No, I haven't. Looks as over-complicated as a DCT.
If you are comparing that to a Carto Tank, I have no more questions.
yup. I have a spheroid matched with a microstick as my stealth, in-the-pocket setup. dude never leaks.
that's what she said.
do you like your coil that high? I've been playing around with height and I think I prefer it about 1mm from airhole to bottom edge of coil. higher seems like more airflow, but muted flavor. lower seems to be more flavor, but less airflow. I'm still testing and parsing the difference, but that's conclusion I'm reaching.
I 'm over a half day now with these generic Amazon.com cotton pads, I think these are the answer never gone this long without burning the wick.
Thank you to whomever discovered the cotton pad wick idea, they are the way to go.
Thank you to whomever discovered the cotton pad wick idea, they are the way to go.
Thats actually about 1.75mm.. Does look high in the pic, but my 1.5mm allen fit with room, and the 2mm didnt.
I was told in this thread to raise it from the 1mm I had before... ?
In fact here is a snap shot of my truck dash board. Taken with an iPhone couple of months ago.
Now that's what I call dedication! I am not worthy! And rather envious!
That's a tough one. Rising altitude has lower air pressure so the air bubble willl expand, pushing juice out. Just like the bubbles that appear and expand when you open a bottle of soda. A valve like you're proposing would probably stop the kayfun working properly as the tank wouldn't be able to suck back juice from the wells (possibly leading to flooding itself). Each draw would lower the pressure of the (increasingly large) air bubble until either the kayfun seals failed, or (probably more likely) the partial vacuum would be strong enough to stop any more juice going up the channels leading to perpetual nasty dry hits.
Rossum's suggestion (storing the device upside-down) is definitely the first thing to try, although you'll probably have to give a couple of priming draws before and (especially) after vaping. You might find a bit of juice working its way down the mouthpiece, though. Failing that, you may have to stick with Genesis-style atomisers in the cab (or move to Kansas)
Hope this helps
What happened to the chatter about the cotton pads, don't tell me its because their something the wife would use. Let me tell ya these things are the answer. I was hoping we would collectively find the optimal coil and cut strip size. Right now I'm using a 1.8 ohm 28 gauge 5/65 coil with 5/16: strip of cotton. We can make this a science instead of a stupid voodoo magic artform.
If you're having trouble locating it Amazon has a generic for $8 with free shipping if you are a Prime member.
If you're having trouble locating it Amazon has a generic for $8 with free shipping if you are a Prime member.
- Status
Similar threads
