Have you asked them if they did? Makes no sense that something just stops working when it always has.. That would annoy the heck out of me!
- Status
Have you asked them if they did? Makes no sense that something just stops working when it always has.. That would annoy the heck out of me!
I will contact then tomorrow. Hopefully trying something different will help. Wick and wire change.
I'd do the same thing as you. Total rebuild and see what happens.
When I used 50/50 vendor juice, I never had to primer pull it after letting it sit. Now with DIY, my 50/50 juice needs a couple of primer pulls before the juice warms slightly and then it works fine. I have plenty of wick in it. I even enlarged juice channels slightly. I can live with it though.
HD
HD
If it's a KFL+, then M2.5 x 0.45 x 5. Check Ace Hardware or maybe Home Depot.
Ehpro KFL+ V2 using 1ohm coil (2.5mm inner diameter, about 6-7 wraps and 0.37mm kanthal) wicking with cotton. Really good flavour and vape! atleast for me. 
Edit. Oh and around 10-14 watts. Depends on juice
Edit2. Second build = Device says 1.3 ohms, multimeter with probe to probe ohm reading 0-1 but mostly 0 says 1.4
5 wraps of 0.25mm on 2mm drill, again using cotton. even better than first build!
Edit. Oh and around 10-14 watts. Depends on juice
Edit2. Second build = Device says 1.3 ohms, multimeter with probe to probe ohm reading 0-1 but mostly 0 says 1.4
5 wraps of 0.25mm on 2mm drill, again using cotton. even better than first build!
Last edited:
Three EHPro Kayfuns - One Lite Plus, two Lite Plus V2. 12-13 wrap 28AWG Ni200 around a ~2.4mm mandrel @ .13-.15 ohms using a Protovapor DNA40 mod. Temperature set at 420F, watts at 18. Wicked with Japanese organic cotton. It's a wonderful thing. 
Three EHPro Kayfuns - One Lite Plus, two Lite Plus V2. 12-13 wrap 28AWG Ni200 around a ~2.4mm mandrel @ .13-.15 ohms using a Protovapor DNA40 mod. Temperature set at 420F, watts at 18. Wicked with Japanese organic cotton. It's a wonderful thing.
I understand that now, thanks to EVOLV's DNA-40 with Temperature Control, ordinary Kayfun could be pushed to higher power?
Because without Temp. Control, look what happened to my insulator when I tried to do that:
You murdered that insulator. Kayfuners in the past have carved out a new one with an old credit card.
Need more power. Just start vaping at 17 watts and that gunk will just vaporize off, lol.
No big deal, I make my insulators from Delrin like this:
This one is for my Fogger, but you get the idea. Let me know if it is not self-explanatory enough, I'll add instructions.
I prefer pictures to words because I'm not native English speaker and I believe that picture is worth 1000 words.
I never used Credit Cards in the past (wrong material) although I used Delrin guitar picks.
Last edited:
When you have a lathe, anything is easy...No big deal, I make my insulators from Delrin like this:
This one is for my Fogger, but you get the idea. Let me know if it is not self-explanatory enough, I'll add instructions.
I prefer pictures to words because I'm not native English speaker and I believe that picture is worth 1000 words.
I never used Credit Cards in the past (wrong material) although I used Delrin guitar picks.
Regards
Tony
Sent from my GT-I9195 through Tapatalk
When you have a lathe, anything is easy...
Regards
Tony
Sent from my GT-I9195 through Tapatalk
Of course
I was actually joking ricks because I know you run lower power. As for thinner or thicker gauges, not sure if it matters. I don't run really dark gunker juices so never experimented on longevity
Last edited:
Wow and they still gunk the coil fast? I know you think they changed the juice, but have you changed anything else? Like the silica lately?
- Status
Similar threads
