I think you'll like it, divrr. I've had a Roller for ages. It's the same switch as the Dingo. Atmizoo makes nice stuff. I use the silver springs in mine. The rhodium springs are also a good add on.
- Status
I think you'll like it, divrr. I've had a Roller for ages. It's the same switch as the Dingo. Atmizoo makes nice stuff. I use the silver springs in mine. The rhodium springs are also a good add on.
More Throat Hit though..
yeah, too much adds more TH or what I just call harshness, but a little bit won't affect it all that much, it's a balance when it comes to coil height here
Well I've finally doing something right....for the past week have just needed to re-do my wicks every other day and setups staying between 1.6 - 1.8 ohms... sure makes things easier.
You must be meaning the small "m tank" I bout .... my pants when I saw 5 euro for m tank. I rushed to the site and was going to buy 5 or 6 if they were the tall m tank haha!!
I just went to the atmizoo site and placed everything I wanted in the cart... the dingo, t2 extensions, bugs, springs, all the extra parts... it added up to $315 with shipping!
Umm... not today LOL
I took the spring out of mine. Just adds to the Vdrop, and I don't use it in 18350 mode anyway. I like my GP Paps 2.5 for 18350 mode.
I don't use 18350s often in anything. I like the form factor; hate the battery life.
yea...when I got my EA mod, I couldn't wait to use the little 18350s...got tired of changing batts so often. I go for batt life over size
I've thought about taking the spring out of the Roller... but I kinda like the little bit of extra protection. If I can get that delrin thing out, I'll try it and see if the vdrop is any less. Although .2 is pretty good.
yea...when I got my EA mod, I couldn't wait to use the little 18350s...got tired of changing batts so often. I go for batt life over size
I've thought about taking the spring out of the Roller... but I kinda like the little bit of extra protection. If I can get that delrin thing out, I'll try it and see if the vdrop is any less. Although .2 is pretty good.
You can get the delrin thing out by putting an allen key in the hole in the bottom of the base, and screwing the center part in. The delrin ring will pop out. If you look at the base, with the Atmizoo writing facing you, you'll turn the center section clockwise.
I got the KFL from VapeRev a couple months ago, then got the KFMini (full kit) from Svoemesto's site a couple of weeks after that and then got the KFL Plus from InTaste.de at the end of Nov. I honestly don't know if I like any one better than the others. Vapor production and quality taste on all three are exceptional! If there's any variance at all, it's probably due to the different coil/wick setups I have on each (don't ask, because I can't remember ). I can say I only have 32g and 0.10 wire at the moment and I use the 32g twisted and single stand - the 0.10 is twisted and they all have cotton wicks, I think. Ohm readings are from 1.5 ohm on the Mini and KFL & 2.4 ohm on the KFL Plus. If I remember correctly, the 2.4 ohm coil is a 5 wrap micro coil with 32g and the other two are twisted wire.
The only problem I've had is with the Lite - it was leaking from the fill screw and that was solved by wrapping the screw with a small piece of Teflon (plumber's) tape.
My Kanger T3s & Evods have pretty much gone into hibernation/backup mode and may soon go into the e-cig museum. I'm still using the ProTanks only because the big KFLs are so top heavy on Spinner/eGo style bats that I usually use for out and about. If I get another mini, that might change too.
). I can say I only have 32g and 0.10 wire at the moment and I use the 32g twisted and single stand - the 0.10 is twisted and they all have cotton wicks, I think. Ohm readings are from 1.5 ohm on the Mini and KFL & 2.4 ohm on the KFL Plus. If I remember correctly, the 2.4 ohm coil is a 5 wrap micro coil with 32g and the other two are twisted wire.The only problem I've had is with the Lite - it was leaking from the fill screw and that was solved by wrapping the screw with a small piece of Teflon (plumber's) tape.
My Kanger T3s & Evods have pretty much gone into hibernation/backup mode and may soon go into the e-cig museum. I'm still using the ProTanks only because the big KFLs are so top heavy on Spinner/eGo style bats that I usually use for out and about. If I get another mini, that might change too.
Last edited:
Just for fun I may get this extension kit:
In super long mode it would be almost as long as two Provais stuck end-to-end!!!
In super long mode it would be almost as long as two Provais stuck end-to-end!!!
Last edited:
I don't think they make the small extensions anymore to triple stack. Intaste does have one longer extension, I should have that one Monday, hopefully I can get it to 10ml mode.
Sent from my SCH-I605 using Tapatalk 2
Sent from my SCH-I605 using Tapatalk 2
Got to this thread through Qorax's link on Fasttech... Does anyone have a picture of the kayfun3.1 or polished lite on VW Nemesis? Im looking for a kayfun for mine (yes, clone) but unsure about the aesthetics... The polished lite seems like a lot of bling, and the 3.1 seems like it has a different finish than the Nemmy.
Thanks in advance!
Thanks in advance!
My brushed KFL might look better but this works better due to better air flow
Both are FT clones, $51 of sheer pleasure.
Or counterfeits if you will.
The bottom one is a Kayfun conversion, I highly recommend this kit to anyone that has a Terminator that's gathering dust. My daily "driver"
Both are FT clones, $51 of sheer pleasure.
Or counterfeits if you will.
The bottom one is a Kayfun conversion, I highly recommend this kit to anyone that has a Terminator that's gathering dust. My daily "driver"
Last edited:
Craig, thanks! Is that kayfun the 3.1 or lite on FT? That looks great on the Nemmy clone actually, not too shiny at all.
It's the $21 FT 3.1, in real life it's quite shiny though,
Nothing a little Scotch-Brite wouldn't take care of.
Nothing a little Scotch-Brite wouldn't take care of.
For those that are buying the Tobeco KFL clones, where are you getting them?
Fasttech has them for $26 shipped as long as your in no hurry for it.
I've got stuff from them in as little as 5 days or as long as 40 days but I always got it.
- Status
Similar threads
