Merlin by Augvape and Roxy

[Btsmokincat]

How's this...

 

[ricks]

Thanks again. So the screw is adjustable in case I need it longer on other mods? Nothing will fall apart?

It adjustable but only a tiny bit. I took my screws off when I first got them for cleaning and checking it out. Looks like it doesn't hold anything together

 

[TheKiddVapes]

That black circle is an o-ring

Sent from my SM-G925P using Tapatalk

 

[CorallineAlgae]

I just found this pic of the top cap and I don't see an oring.

View attachment 561413

There should be one in the spares bag. A lot of people either lost it when first cleaning the tank or it wasn't installed at the factory. They seem to pop out easily. If it turns out that you want spares these look like a possible 1:1 replacement.

 

[tmcase]

The black ring in the center around the opening of the center tube is an oring. It seals against the flat area inside the top cap.

Oh, ok. I have an oring there.

 

[tmcase]

Thank you all for your response. I do have that oring in place.

 

[TheKiddVapes]

What I was told is that the top o-ring allows the tank to create a vacuum and stop leaks.

Sent from my SM-G925P using Tapatalk

 

[tmcase]

How's this...

Perfect.

 

[LilWhiteClouder]

Loving the Merlin I just received today Fits perfectly on my Arctic Dophin v1.

I popped in the Notch Coil that came with it since I am at work. An amazing vape. I love the little wick tail troughs on each side by the juice intake holes.

 

[TheKiddVapes]

It adjustable but only a tiny bit. I took my screws off when I first got them for cleaning and checking it out. Looks like it doesn't hold anything together

Which screws? The post/grub screws?

Sent from my SM-G925P using Tapatalk

 

[ricks]

Which screws? The post/grub screws?

Sent from my SM-G925P using Tapatalk

The positive screw on the bottom of both my Merlins. I took them out when I first got them to clean them.

 

[TheKiddVapes]

The positive screw on the bottom of both my Merlins. I took them out when I first got them to clean them.

Ok those are a screw that's in the center of the base with a hole in it?

Sent from my SM-G925P using Tapatalk

 

[tmcase]

Ok those are a screw that's in the center of the base with a hole in it?

Sent from my SM-G925P using Tapatalk

No, the screw on the 510 connection.

 

[ricks]

↑↑↑↑ What she said

 

[TheKiddVapes]

Ok, still at work but in thinking rick.....I'm trying

Sent from my SM-G925P using Tapatalk

 

[Haylon357]

I'm still having some dry hit issues. Am I supposed to tuck the cotton where you can see it through the juice hole?

Sent from my LG V10 using Tapatalk

 

[ricks]

I'm still having some dry hit issues. Am I supposed to tuck the cotton where you can see it through the juice hole?

Sent from my LG V10 using Tapatalk

How thick is your juice.? What VG/PG ratio

 

[dave51]

I'm still having some dry hit issues. Am I supposed to tuck the cotton where you can see it through the juice hole?

Sent from my LG V10 using Tapatalk

I sit my cotton right on top of the cup if you can see any at all through the hole its very little
I do make sure the tails go all the way to the bottom up to the front of the channel
I have run a 26ga 1.0 ohm coil up to 50 watts with no dry hits while chain vapeing
I would have gone higher but it got a little hot for my taste

 

[TheKiddVapes]

↑↑↑↑ What she said

Why don't you try putting a washer or shim?

Sent from my SM-G925P using Tapatalk

 

[Martin Vataj]

Got 2 Merlin's 2 days ago from eciggity...one stainless and one black ....loving the tanks but my black one has a really loose juice flow control ...turns with little to no effort...the stainless one is perfect ....contacted eciggity and this what they told me


"Weare going to contact the manufacture if they can send us replacements for the loose AFC rings.It seems that this is a common issue for the Black Merlin. We will let you know once we are contacted back.