Mods by Chels - mini-ecig

[Slots]

I use the mini vivi nova with 1.8 dual coils. they work great.

The Mini ProTanks work great too.

 

[SteveMc]

That's a good looking setup, I want a spheroid but I'm having a hard time locating one so I might go with this. I have some batteries on the way so the only thing holding me back is a juice box lol. Maybe I'll give one of these a try. And what exactly is a clogger??

http://www.vapourart.com/ is the official site for the GP Spheroid, great service from them.

 

[FACE MEAT]

We recommend the MiniGen and MiniAtty, and believe they compliment the MicroStick perfectly!
However, MicroStick accepts any 510 atomizer up to 16mm in diameter. The bottom air fed tanks, cartos are also ok. The 510 connector is shorter than normal, so the atty is never fully screwed into it. There always be enough space between the connector and the bottom of the atty for the air flow.
Don't try to drill the MicroStick to increase the atomizer hole. This will ruin it.

The biggest discussion about the atties for the MicroStick is here:
MicroStick Atty Options

The most popular atties to be used with the MicroStick are MiniGen, Hellfire Mini, Spheroid, Kayfun Mini, DocDave MiniMicro, etc. But there are more options.

Rebuildables:
A7
Animodz ChowChow
Animodz DoggyStyle
Arashi Mini V1
Atmomixani Steam Machine Dripper
Bulli Smoker A2
Docdave Mini-B (16mm)
Docdave Mini Micro (16mm)
GP Spheroid (16mm)
Gurman V2
Gus Aiolos (16mm)
Hellfire Micro Mini (16mm)
Hellfire Mini (16mm)
Kaifun (14mm)
Line LE (14mm)
Line SS (14mm)
MM Vapors Mini-DID (14mm)
MM Vapors Temon (16mm)
MiniAtty (16mm)
MiniGen (14.5mm)
Nahaul (16mm)

Phoenix XL RDA (16mm)
Piculisci
Qzi Mini (16mm)
RGM2
Ruthless Mods Havoc (16mm)
Sturm G-Tank (15mm)
Sofia/Diver(v2)/Killer + 45mm Slim Tank or Grail
SvoeMesto Kayfun Mini (14mm standard, 15mm Mak. tank)
Taifun V1/V2 with cotton tank

Tanks:
Titanide
Boge F-16

Others:
Aspire Mini Vivi Nova
Aspire K1

I added the Aspire K1 to the list. It's the same diameter as the Aspire Mini Vivi Nova but uses a smaller version of their BVC coil. It's a fantastic little atty.

 

[LittleDonkey]

We launched 2 new long awaited products:
- MiniStick: 18500/18650+Kick, 23.5 mm atty hole
- MidAtty: 22mm silica & mesh atty

MiniStick is a relatively small mechanical mod for 18500 batteries. With 18650 extender it can be used with the Kick, which is located under 510 connector making the MiniStick one of the smallest mods in this category.
MiniStick has 23.5 mm atty hole, which allows using any atty 23 mm in diameter or less.

We recommend our new atomizer MidAtty to compliment the MiniStick.

MidAtty is a larger version of the MiniAtty. It's a silica and genesis style atty. So it can be built with silica, cotton or mesh. It has adjustable air flow (1.3 mm - 1.9 mm), adjustable liquid flow and a glass body.
MidAtty has tripple air flow for better taste and insulators made of peek.
The production is ongoing. We will perform the shipping in 20 working days after the order is placed at most. The factory is now well established and there will be no more delays.

The MiniStick price is $129, the same as for the MicroStick. The leather case from Parish is $64 including free shipping from Russia.
The MidAtty is only $70! Also we offer kits to save on combined orders.
MiniStick Black (shipping within 20 business days) - Mini ECIG
MidAtty (shipping within 20 business days) - Mini ECIG
Kit: MiniStick + 18650 extender + MidAtty - Mini ECIG
Kit: MiniStick + 18650 extender + MidAtty + leather case - Mini ECIG

 

[LittleDonkey]

We're about to start production of the 2 new drips. We want them to be ideal, so we need your comments and ideas.
While we're working on prototype, it's fairly easy to make changes. Don't hesitate and take your chance to make them better

We want good staff to be affordable. Just look at the prices!
MiniDrip (22 mm). Only $30.
MicroDrip (16 mm). Only $20.

The prototype will be ready in about 1 week. The sales will be started in 2 weeks.
Now we would like to know what is the demand. Please, subscribe to show your interest:
MiniDrip (sales start in 2 weeks) - Mini ECIG
MicroDrip (sales start in 2 weeks) - Mini ECIG

Both drips are made of SS 316. Probably, there will be an extra option: a fully glass body for $7. Is it needed?

MiniDrip:
Dimensions:
- diameter - 22 mm
- length - 39 mm
- capacity - 2.5 ml
- air hole - can be adjusted: 1.3 mm, 1.5 mm, 1.7 mm or 1.9 mm

Features:
- fully made of SS 316
- refilling with removed top cap
- no-spill top cap (to prevent leaking in horizontal position)
- multi-start threads in the top cap (to unscrew it in half-turn)
- pins with philips screws
- adjustable air flow
- triple air flow
- peek insulators

MicroDrip:
Dimensions:
- diameter - 16 mm
- length - 43 mm
- capacity - 2 ml
- air hole - 1.5 mm

Features:
- fully made of SS 316
- refilling with removed top cap
- no-spill top cap (to prevent leaking in horizontal position)
- multi-start threads in the top cap (to unscrew it in half-turn)
- pins with philips screws
- peek insulators

 

[Mark Denison]

Mods by Chels you are one of the only ecig companies with amazing products at amazing prices! I just wanted to thank you for all that you do for the vaping community!

 

[slyphex]

I am so excited about the MiniStick, I just heard about it this morning and ordered one. This is literally something I have wanted ever since I started vaping. Specifically the part where a Kick fits under the atty with the extender

 

[Dontknow]

I am so excited about the MiniStick, I just heard about it this morning and ordered one. This is literally something I have wanted ever since I started vaping. Specifically the part where a Kick fits under the atty with the extender

Me too. Ordered as soon as I saw it. I modded a standard MS to take a kick, rather agricultural modification, but it works a treat. But now, built for a kick with a bigger atomiser - brilliant!


Sent from my iPad using Tapatalk

 

[Ramjet]

Ok...so the MiniAtty arrived yesterday. The atty arrived in perfect condition and so did the additional items placed in my order. This arrived about two weeks from the time they emailed me of delivery. I live in Minnesota/USA.

The MiniAtty seems extremely well made. While contemplating this atty over several months, I had concerns that after a few puffs I would get a dry hit. This did not happen. I built a 1.2ohm coil (5 wrapes of 30g on a large syringe needle) and threaded cotton as the video suggested. I'm using 70/30 pg.vg. Liquid. Opened the feed wide open and WOW! Great vaper and flavor. In about 20 minutes, liquid is coming out the air inlets. Dang it. Ok then, empty remaining juice onto a towel, clean excess off and close feed to about 1/2 throttle. There, load up and try again. Same great taste, vapor and draw is effortless. Non of that "wait for it" with this atty. The draw is as easy as a stock rm2. Perfect! But, 20 minutes into it again and juice is filling up the Microstick again. Darn it. Same thing. Spill the juice, clean and close the feed. New cotton just because I'm there and thought, let's start from the beginning. Load up the cotton with juice and proceed. After about 30 minutes I had a very faint cotton taste. Took out the shekel that came with it and opened the feed about an 1/8th. The thickness of the coin. It's perfect! No leaks and really great vapor, throat hit and incredible taste.

I'm going to go out on a limb...this is compatible with my REO. Yes, I said that. Taste, draw and vapor are very much alike. As far as the Spheroid, MiniAtty beats it for taste, vapor, draw and throat hit. Yes, I said that too. I like the fact that I can use cotton with this and my REO. The Spheroid needs silica wick and that tends to taste burnt to soon using NET liquids as I do.

Again, I need to emphasize the draw on this. It's almost effortless and I'm surprised at how much vapor comes outa this little thing. Oh, did I mention the popping sound it gives off. Sorta like fresh tobacco burning in there, but it's not




Thanks Chels
Well worth the money!

 

[Susan W.]

Does anyone have a comparison between the MiniAtty and the Sophia? I wasn't that fond of the Spheroid due to the fluff and the flavor I get from the Sophia is better than from a Spheroid, IMO. I'd be willing to get the MiniAtty if it's comparable to the Sophia though.

 

[LittleDonkey]

The MiniAtty seems extremely well made. While contemplating this atty over several months, I had concerns that after a few puffs I would get a dry hit. This did not happen. I built a 1.2ohm coil (5 wrapes of 30g on a large syringe needle) and threaded cotton as the video suggested. I'm using 70/30 pg.vg. Liquid. Opened the feed wide open and WOW! Great vaper and flavor. In about 20 minutes, liquid is coming out the air inlets. Dang it. Ok then, empty remaining juice onto a towel, clean excess off and close feed to about 1/2 throttle.

The problem is that the liquid went to the deck directly, not through the wick (as planned), but directly. When you're building a MiniAtty (and other similar atties with holes for the wick in the deck), you need to fill those holes with the wick (cotton). Then liquid will get to the deck and to the wire only via the wick. Just build the MiniAtty once again and make sure that the holes in the deck are carefully filled with the wick.

Thanks Chels
Well worth the money!

Thanks for the kind words

 

[Ramjet]

Yep, that explains it perfectly. I also stopped trimming the tails and just pulled them through the base, then cut off flush and tucked them into the cavity. No more leaks

I should mention the MiniAtty's learning curve was very short lived. After two* tanks of NET juice, I pull the cotton wick out, dry burn and re-wick. If I didn't use NET, I'm sure I could run many, many more tanks through before re-wicking. Once again, the flavor is awesome and the vapor is incredible. I'll be buying another soon as a backup.

Thanks little donkey!

 

[LittleDonkey]

Christmas is coming and we have great news and discounts!
.
First of all, MicroSticks of all colors are in stock and with discounts.
.
Second, the prototypes of the MicroDrip (16mm) and the MiniDrip (22mm) are ready!
Our first reviewer is exited about them, so we are ready for the mass production with shipping in 3 weeks.
.
We decided to attack the clones in a new way. The price is as low as for clones, but they are original!
MicroDrip - $20
MiniDrip - $30, with SS tubes for combined glass body - $40
Share this proposal on forums and in groups to help to keep the prices low.
.
MicroDrip perfectly compliments the MicroStick, so you can get an extra discount ordering them together as a kit..
.
Merry Christmas!
.
Links:
MicroStick Black (IN STOCK: shipping within 1 week) - Mini ECIG
MicroStick Red (IN STOCK: shipping within 5 business days) - Mini ECIG
MicroStick Gold (IN STOCK: shipping within 5 business days) - Mini ECIG
MicroStick Blue (IN STOCK: shipping within 5 business days) - Mini ECIG
MicroDrip (shipping within 3 weeks) - Mini ECIG
MiniDrip (shipping within 3 weeks) - Mini ECIG
Spare parts: set of 2 SS tubes for combined MiniDrip body (shipping within 3 weeks) - Mini ECIG
MicroStick + MicroDrip kit (shipping within 3 weeks) - Mini ECIG
.
MiniDrip:

.
MicroDrip:

.

Reviews:
MicroDrip - YouTube
MiniDrip - YouTube

 

[Arnold Ziffle]

woo hoo,the micro big is just what I was hoping for. love my microstick. the new drippers look great too. imagine a micro big with a kayfun nano. I'm gonna have to have all three. you guys are doing great work bringing authentics to the market at clone prices. when I took my hamoriko into a vape shop and asked them how much I paid for it they thought between 150 and200. I should just mail you my wallet.

 

[LittleDonkey]

We can start BigMicros after the MiniSticks are ready if there will be at least 100 subscriptions for the BigMicros.
So if you want it, please let us know here:
MicroBig Black (investigating demand) - Mini ECIG

 

[LittleDonkey]

Merry Christmas and happy holidays!
Have a great time with your family and friends!

We still have discounts in the store
Mini ECIG

 

[btobw]

Arrived while I was away over the holidays ... and it's very pretty. To my eyes it's more of a teal blue than in the pic, but I suspect my blue/green colour perception leaves a little to be desired. Now I have two microstick/miniatty combos to love

 

[Mark Denison]

Have the mini sticks started shipping yet?

 

[LittleDonkey]

Have the mini sticks started shipping yet?

Not yet. There were problems with coverage so we sent them back. Hope to get them in perfect condition in several days. Then we'll start the shipping.

 

[LittleDonkey]

Arrived while I was away over the holidays ... and it's very pretty. To my eyes it's more of a teal blue than in the pic, but I suspect my blue/green colour perception leaves a little to be desired. Now I have two microstick/miniatty combos to love

Looks awesome!