How about sealing with a silicone boot at the bottom, just pierce the silver wire through. The top may stay open though. Great prototyping the bare battery test looks like a blast.
Sent from my Nexus 7 using Tapatalk 2
New Genesis type atomizer by DID!
- Thread starter Jim Damianidis
- Start date
- th_trl_thread_readers 0
- Status
How about sealing with a silicone boot at the bottom, just pierce the silver wire through. The top may stay open though. Great prototyping the bare battery test looks like a blast.
Sent from my Nexus 7 using Tapatalk 2
Hi specialists have some problem with my new Temon Set. cleaned everything in a ultrasonic bath
I tried twenty setups ore more with different wicks. The Temon ( Mini DID ) Atomizer produces a lot of clouds on my Provari at 3,2 Volt with 1.1 Ohm.
When I screw it on my Temon Bat it produces less than the half of clouds with an fresh IMR AW 14500.
Why this??????
it tried tests with my multimeter. Under fire with an fresh battery there only come 2,6-2,8 Volt direct on the Atomizer hold it on +and - directly on the Atomizer.
Why this.
IT testet it with a longer center post without the spring .....but it is the same .
I have no idea anymore...but so I have no fun with this Set.
Hope you have an other idea for me
thx
Herby
I tried twenty setups ore more with different wicks. The Temon ( Mini DID ) Atomizer produces a lot of clouds on my Provari at 3,2 Volt with 1.1 Ohm.
When I screw it on my Temon Bat it produces less than the half of clouds with an fresh IMR AW 14500.
Why this??????
it tried tests with my multimeter. Under fire with an fresh battery there only come 2,6-2,8 Volt direct on the Atomizer hold it on +and - directly on the Atomizer.
Why this.
IT testet it with a longer center post without the spring .....but it is the same .
I have no idea anymore...but so I have no fun with this Set.
Hope you have an other idea for me
thx
Herby
Last edited:
Sounds like bad contact. What voltage measured with the top cap off and coil installed.
Possibilities:
1. Voltage drop is from a bad quality battery.
2. Internal resistance from the spring.
Try pushing the spring as far into the hole on the underside of the top cap to the battery tube as possible.
1. Voltage drop is from a bad quality battery.
2. Internal resistance from the spring.
Try pushing the spring as far into the hole on the underside of the top cap to the battery tube as possible.
I did remove the spring and made a longer center pin so that contact is better...but the same problem batteries are new AW IMR 14500 without protection. maybe it could be the spring in the bottom cap ?
Try testing the battery voltage, or try it in another device. It is possible, even with AW's, that you have a bad battery.
battery voltage is 4.2 Volt fresh loaded ...but I have no other 14500 mod....but all 4 battery´s could not be bad
Just send a message through the MMvapors website Herby.
I am sure Jim can and will help you out here since he does have the best customer service in the world!
I am sure Jim can and will help you out here since he does have the best customer service in the world!
GOOOOD MOORNIIING!!!!
Thank you Miriam!!
Hi Herby I think this is the spring!
Please pull the spring to see if is tight enough in to the positive pole screw.
The last that I would do is to test it without the spring and check the voltage again!
I will be here today Sunday waiting for your reply
Thank you Miriam!!
Hi Herby I think this is the spring!
Please pull the spring to see if is tight enough in to the positive pole screw.
The last that I would do is to test it without the spring and check the voltage again!
I will be here today Sunday waiting for your reply
Tony with everything Jim has coming and everything he hasn't thought of yet, you may just want to redirect some if your pays automatic deposit to MMVapors account. 
Ain't life grand!! Time for me to have hubby set up an automatic pay account, like you suggested for Tony I think it was. Great idea!
It's a size 28mm, which will make our Silver Bullet, LavaTubeV2, etc look hybrid! I love it.
Yes vote from me too! My Bam could use a fitted atty. I don't know if I'd be able to pick it up without renting a forklift, but it sure would look nice and last a whole 2-4 days to boot! Shoot, in time I'd even get the mod too, if Jim makes one. Great idea!
Congrats! It's a lovely mod, I love mine a lot. It's comfortable in hand, and can be adjusted to any size ... the button is fabulous, like pushing a flat keyboard key only better, it's shiney but doesn't fingerprint up gawd awful like most shineys do, and they update/upgrade any and all important functional parts for free. My updates are in the mail, probably in customs, and when they get here, my DID's will sit flush and pretty, and the new silver plated button connection will fire like mad each and every time. It's truely a pleasure to change the batteries out, with the battery cap on the end. Most telescopic mods make us twist for forever the tubes, for battery changes. Not the Roller! It's a real treat to use. Plus, the short stop fuse works in every battery size too, because of the battery cap spring.
As you can see, it has a lot of pluses going for it.
I just saw your Christmas Day Contest !
What a truly generous and exciting contest !
I can't wait to see which one of you gets it !
What a truly generous and exciting contest !
I can't wait to see which one of you gets it !
WHOAAAAAAAAAAAAAAAAAAA NELLY!!!!!!!!!!!!!!!
O M G!!! Just wrapped a new coil on my Standard DID and when I went to put the wick back into the coil after testing the ohms I accidentally ripped the outer layer about midway down the wick so it would not go back in. So I grabbed my back up wick for it,(Yes I am always prepared for such problems), and it was a hair thinner than the other one. So I just reverse rolled it to loosen it up a hair so it would fit nice and snug into the coil. IT HITS AMAZING!!!! Wicks Perfectly!!!! Loose Wicks ROCK!!!!! Way better than my tightly rolled one!!!
Just thought I would share
Hope everyone is having a great day
Nate
O M G!!! Just wrapped a new coil on my Standard DID and when I went to put the wick back into the coil after testing the ohms I accidentally ripped the outer layer about midway down the wick so it would not go back in. So I grabbed my back up wick for it,(Yes I am always prepared for such problems
), and it was a hair thinner than the other one. So I just reverse rolled it to loosen it up a hair so it would fit nice and snug into the coil. IT HITS AMAZING!!!! Wicks Perfectly!!!! Loose Wicks ROCK!!!!! Way better than my tightly rolled one!!!Just thought I would share
Hope everyone is having a great day
Nate
- Status
Similar threads
