OBS Crius RTA?

Status
Not open for further replies.

Roadtrip635

Vaping Master
ECF Veteran
Aug 29, 2015
6,110
10,358
Texas
HMMMMMMMMMM
Anybody see the new ijoy reaper plus?

Smaller capacity than the crius but same top fill, top airflow.........
So far can only find the actual ijoy video.



dna has it for 30 and have seen cheaper elsewhere.
iJoy Reaper Plus Sliding Top Fill Sub-Ohm Tank
I'm intrigued.

I've been checking that one out too. A sub-ohm tank with a v-deck rba, sounds great, even has a large selection of coils, even ceramic. Could be a pretty decent all purpose tank. That guy chugs that wine at the end of the video, that was great!
 

Gallant

Ultra Member
ECF Veteran
  • Dec 4, 2013
    1,006
    1,582
    Edmonton, AB, Canada
    My best OBS build so far
    Dual vertical SS 316L 24g 6 wraps 2.5 mm ID

    20160108_115010.jpg


    20160108_115119.jpg
     

    Gallant

    Ultra Member
    ECF Veteran
  • Dec 4, 2013
    1,006
    1,582
    Edmonton, AB, Canada
    How'd you manage to get that stuffed into the tank without wrecking the cotton? I couldn't get that for the life of me.
    Easy! cut 4 pieces of cotton bacon feed them 1 by 1 into the juice holes pull them down then cut them from the bottom of juice hole pull it back up till it reaches about half way through the juice hole then cut the top about the height of the build post. Take a piece of Japanese cotton peel the top off & cut enough to wrap the entire circumference of the build trim any extra & your good to go!
     

    AMDTrucking

    Ultra Member
    ECF Veteran
    Dec 7, 2013
    1,950
    3,232
    California

    roxynoodle

    Unregistered Supplier
    ECF Veteran
    Jun 19, 2014
    15,344
    37,213
    Ohio
    Well maybe someone will order the reaper plus, cough @roxynoodle cough. That way we could get a side by side pic of the rba decks. But the tank is slightly wider than the crius so it must be very short with that capacity.

    Get the Griffin :)
     

    KenD

    Vaping Master
    ECF Veteran
    Aug 20, 2013
    5,396
    9,257
    48
    Stockholm, Sweden
    kennetgranholm.com
    So, I received my Crius clone (black) from fasttech today. I don't dare say anything definitive about leaking yet, but thus far it's dry. Quality is definitely not worse than the original. For example, the grub screws on the original would cut my leads but the ones on the clone won't. The insulator will most likely hold up much better as well.

    On a sadder not; the black replacement glass I got won't fit either the clone or the original :-/

    Sent from my M7_PLUS using Tapatalk
     

    Rizzyking

    Ultra Member
    ECF Veteran
    Verified Member
    Aug 15, 2013
    1,391
    1,956
    East Midlands, United Kingdom
    Shame on the glass Ken but sounds as though the clone tank is a keeper, my three haven't left fasttech yet but they were only small part of the order and couple of things were out of stock when I ordered so expected a delay. Doesn't sound like there are any glaring issues to watch out for which is nice.
     

    Gallant

    Ultra Member
    ECF Veteran
  • Dec 4, 2013
    1,006
    1,582
    Edmonton, AB, Canada
    my three haven't left fasttech yet but they were only small part of the order and couple of things were out of stock when I ordered so expected a delay.
    Ask them to split ship they usually do that when part of your order is ready to ship while the other part is waiting restock
     
    Status
    Not open for further replies.

    Users who are viewing this thread