it leaks from the center post or from the 510 threads soul?
Odysseus official
- Thread starter imeothanasis
- Start date
- th_trl_thread_readers 0
-
- Tags
- halo madvapes provari revolution
- Status
it leaks with the mouthpiece closed?
it leaks when you refill only?
Are you sure that you screw the ceramic housing very well inside Ody's base?
Is the center post screwed well on the ceramic housing?
it leaks when you refill only?
Are you sure that you screw the ceramic housing very well inside Ody's base?
Is the center post screwed well on the ceramic housing?
I have found if I leave it closed, not tight closed, but closed, I get "dry" hits.
I have to run out to the Post Office before it closes today.
I'll be back shortly to check on this thread.....
Thank you Imeo, for trying to help me figure this out.
I'll be back shortly to check on this thread.....
Thank you Imeo, for trying to help me figure this out.
Yeah that is a bummer. I just PM'ed Bruce asking if he could send it along with my Penelope that will be shipping soon. Hopefully that'll be okay with him. Even though it's 'usable without' I personally like that extra insurance that my ceramic will be okay. Plus is makes loosening and tightening the lower post but much easier.
Sorry Imeo I have not yet, had to get to work very early. Will try when I get home, but do you suggest taking apart the full rebuildable part for a wash?
Mine shipped 6/26 from Florida and is now in Kansas city Ks.I live in S.W.Missouri?USPS goes the long way around.
you can just boil it assembled, I am sure it will be ok Brand
Well i have my ody gents but no wire for it the wire i have broke off on one side so i had to twist it togeather, my locking ring cut the living shot out of one side of my wick so im rocking it 1/2 krinkle, but all in all im happy, its vaping okay. But i know its not running on all cylinders
the wire i have broke off on one side so i had to twist it togeather, my locking ring cut the living shot out of one side of my wick so im rocking it 1/2 krinkle, but all in all im happy, its vaping okay. But i know its not running on all cylinders
Imeo, what is the size of the O-ring that goes into the ceramic that we're missing? Perhaps I could pick one up here in town to use until the one from Bruce gets here?
Once again though, the Ody is TRULY a work of art! Very well built, wonderful craftsmanship. Can't wait to get my hands on a SS GGTS and my Penelope! I'm now a huge fan of yours!
Once again though, the Ody is TRULY a work of art! Very well built, wonderful craftsmanship. Can't wait to get my hands on a SS GGTS and my Penelope! I'm now a huge fan of yours!
Sorry for the continuous questions Imeo... But now I should boil it? Or just wash it with dish soap and water..? Boiling it sounds like it would really do the trick, just worrying about the O rings/ceramic part, they'll be okay? If not too much of a hassle, could you please let me know the steps that you would suggest? Thanks a billion!you can just boil it assembled, I am sure it will be ok Brand
I cant get my ody to work. I have now built 4 coils and still the same thing. When I put it on my provari I get e1 error message. Cant get it to fire. Put it on ego and silver bullet with the same outcome. Watched Scott's videos and Phil's and am doing everything exactly the same. What am I doing wrong?
Side note... My ody has a metal channel on one side of the ceramic channel where in all the videos I have watched they don't.
Any help would be greatly appreciated.
Side note... My ody has a metal channel on one side of the ceramic channel where in all the videos I have watched they don't.
Any help would be greatly appreciated.
Not always with the mouthpiece closed, but yes, at times.
It leaks from about half full down to almost empty.
Usually. I do have times when it leaks no matter how much is in the tank.
Also, this is usually with large mode, I do get occasional leaks in short mode.
This can either be first fill after building a new wick/coil, or refills.
The ceramic housing itself, I believe all parts are put together correctly, and flush/tight.
When I make a new coil/wick, I put the knurled ring over the top.... maybe a few cm. Just far enough to hold everything.
Then I screw the rebuildable part into the base as far as it will go. (I'm using the GG base, not the 510)
Then I tighten the knurled ring down until it is flush and tight against the base.
Then I put the mouthpiece on. Firm, but not tight tight. Just until it meets the ring as I figure I will be loosening it eventually anyway. I was putting it on tight, but was worried I was unscrewing the housing so I stopped doing that. Either way hasn't made the leaking less.
I have had the housing and base so tight it was difficult to get them back apart.
And, as I put above, I believe all parts of the housing are well connected.
If I attempt to wiggle anything, nothing moves.
Hi, jebey. You have the latest version of the Odysseus which is why you have the metal channel.
Have a watch of Navy_Lifeguard's excellent tutorial. He uses the very same version Ody that you have so if you follow his steps you should be good to go
http://www.e-cigarette-forum.com/forum/gg/23262-gg-reviews-25.html#post6402684
What works for me is the one with the metal channel on that side of the ceramic. The coil will always be on the out side of the ring.
So this is my first time posting here but felt the need after receiving my Odysseus order today. I purchased one in short mode & 2 in drip mode through COV, and got my order today. Now I am a dripper so I also purchased additional adapters to turn the one in short mode to drip mode. I now have three that are in drip mode & this is my first experience with rebuildables. In one hour I had all three working perfectly on my first try, all at about 2 ohms. I have to say that I have never gotten better flavor out of my juices until using the Odysseus. I just wanted to give my thanks to Imeo for making such a wonderful product & they work so well that I noticed Bruce still had some drip modes in stock & I had to purchase another, I also have a Penelope on pre-order. At first I was a little nervous about purchasing so many without first trying the product but now I can say my fears are over and I am in vapey bliss.
I also want to thank all the wonderful people that post here, as if it was not for you guys I would probably not have made the purchase.
Again thanks to Imeo, and everyone here for helping me make such a wonderful purchase,
Dave
I also want to thank all the wonderful people that post here, as if it was not for you guys I would probably not have made the purchase.
Again thanks to Imeo, and everyone here for helping me make such a wonderful purchase,
Dave
- Status
