OFFICIAL avidvaper.com Clean Tank discussion thread

[strout]

Did I mention I love my clean tank?

 

[RickHerron]

*removed by poster*

 

[RickHerron]

*removed by poster*

 

[RickHerron]

*removed by poster*

 

[tyleris12]

After you read that post, and then re-read this one, tell me who is the "troll". If you're really interested to see WHO's been getting slammed here, then find some of my other recent posts and read those, too.

RickHerron, tybin is one of THE NICEST people here on ECF and I know she was not trying to be rude or disrespectful in any way...only trying to help, so I think you just misunderstood her! Sometimes when you are reading something it is hard to know exactly how it was meant, as you can not see someones expressions or hear their tone of voice. I was trying not to post during all of this, but I can't just sit back and see someone talk badly about one of the most helpful people here!!!! If you were already upset about something else, some other thread/post, than maybe you should have not taken it out on the wrong person....just sayin'.......

 

[RickHerron]

*removed by poster*

 

[tybin]

(((Rick))).


Now that we have all sufficiently given our lovely clean tanks, some good exposure, here's to a great day to all and wishes to good success to jj

 

[7less7]

Gone a few days and I see my thread full of life...
neat!
Hope everyone is doing well and what not, super busy with my real job, getting materials in order for the next batch, hopefully have some for Florida's vapevest/bash/stock/thingy....

 

[andel11]

Love my Tank, Thanks 7less7

 

[Killjoy1]

^^^ Ditto

 

[CheekyMonkey]

Gone a few days and I see my thread full of life...
neat!
Hope everyone is doing well and what not, super busy with my real job, getting materials in order for the next batch, hopefully have some for Florida's vapevest/bash/stock/thingy....

Any chance there will be a few colorful clean tanks at VapeStock?

 

[MikeE3]

Good Evening All!

I'm loving the looks of my duo tank, but I do have a question or two for use.
-Top o-ring seems to slip up every time ending in half of the oring being in the seal, the other half bulging out of the top...
-bottom oring holds my carts like a vice grip. Slash only specific drip tips can be used to install a cart... and I broke my last tip this morning :/. I'm glad it doesn't slide around or leak or anything, but holy crap. I've had to change it twice (cart issue, not tank issue) and it's been about a 10 minute power struggle each time.
- flooding/ vacuum- when I put the cap on, it floods. seeing as though not everyone is having this issue, it sounds like its something I'm doing, but I have the air bubble over all of my holes, and am half filling the tank just so I can make sure I have plenty of air around the holes. As for the vacuum. I can take the top on and off if I have a full tank, but if the tank has been vaped on and its empty, it hurts my fingers to take the cap off, and usually requires me to wrap the tip in a towel and the tank in a silicon kitchen gripper.

Anyone else running into any of these things? Any advice on how I might be able to modify what I'm doing to make the tank easier to use?

Only other advice I have- since 3/4's of my drip tips won't let the cart slide up the bottom oring- including a specific drip tip, or recommending one would be awesome.

First off - I don't have one of these fine looking tanks. What I'm going to say is from experience with other tanks.

I had one tank that just flooded. Tried different carto's, smaller holes in the carto, 1/2 fill the tank, make sure air bubble was over carto hole. Tried it all and the tank just flooded. I could watch the juice level go down. I gave it 1 more try before tossing it and noticed 'tiny, tiny' little air bubbles at one end of the tank just under the cap after taking a vape.

I replaced the o-ring and the tank worked fine. I can only assume the o-ring was damaged or whatever and there was a micro air leak causing a pressure problem in the tank and forcing the juice out.

 

[njgeek]

I no longer have a flooding issue thanks to the fine folks of this forum. 75%PG, single bit hole from a 1/4" punch. Tipping the tank and snapping the cap fully on without liquid over the hole did the trick.

 

[little1199]

First off - I don't have one of these fine looking tanks. What I'm going to say is from experience with other tanks.

I had one tank that just flooded. Tried different carto's, smaller holes in the carto, 1/2 fill the tank, make sure air bubble was over carto hole. Tried it all and the tank just flooded. I could watch the juice level go down. I gave it 1 more try before tossing it and noticed 'tiny, tiny' little air bubbles at one end of the tank just under the cap after taking a vape.

I replaced the o-ring and the tank worked fine. I can only assume the o-ring was damaged or whatever and there was a micro air leak causing a pressure problem in the tank and forcing the juice out.

Between your post about orings, and the post below mentioning carto punching, maybe it's time to fix my carto technique. I've been running three hole in these. I'll give two hole and one hole a try and see how that works out while I'm waiting on orings. Thanks for the advice!

 

[Sinean]

Couldn't resist !!! Had to buy The Parva One Piece. I like that there are no end caps, nice modern clean design! I may have to try the 2-piece in the future.

 

[tybin]

loving my dynamic "duo"

 

[MikeE3]

Between your post about orings, and the post below mentioning carto punching, maybe it's time to fix my carto technique. I've been running three hole in these. I'll give two hole and one hole a try and see how that works out while I'm waiting on orings. Thanks for the advice!

Wow - 3 holes! I put 1 1/16inch hole with a drill bit in my carto's and for me it works well using juice ratio's from 70/30 to 20/80 PG to VG. YMMV

 

[7less7]

I lil vape pr0n...

 

[chet]

nice
the pawn tip on the very left on mini provari seems shorter than the pawn tip on the middle provari.
Is there an option? I really like the shorter one.

 

[7less7]

Just bought me one of these....
ProVari Mini Satin Black Variable Voltage Electronic Cigarette