Official ProVari Radius Thread
- Thread starter Vape360
- Start date
- th_trl_thread_readers 0
- Status
Haha great point! And there's a 2.5 mini just begging for me to pull the trigger on a p3 conversion ;-) If I get enough p3 threaded attys I might have to pull that trigger.
- Another Kabuki (fingers crossed on maybe seeing an updated version sometime
- Fingers crossed for another product from svoemesto. I've heard rumors on something for the MTL crowd and - - "here's hoping!"
- Calix after side air, p3 base, PMMA, etc. $ is earmarked and everything. Can't wait!
And I'm the same! EASILY 2 full days - whether at 13 watts KF4 boost 3, or 11.2 with boost 2 on the Kabuki. Easily.
Sent from my SM-N920V using Tapatalk
Last edited:
And my lord is the 18350/Kabuki combo amazingly small and transportable!
Sent from my SM-N920V using Tapatalk
RB, I think it doesn't hold 3 mls ... I measured using a syringe, yesterday. I got a drop shy of 2.5 mls. Doesn't much matter; I'm not complaining! I was just concerned that there might be an issue cuz all y'all said your battery was lasting days and days. I can't get a full day out of an 18650 in a P3, either. Prolly I just vape too much
Or too often. I am a chain vaper, just like I smoked. I chew through batteries. Never gave it much thought. By hitting your PV more often, the batteries don't get as much rest time as a vaper whom may take less frequent hits on their PV. Hitting a battery in a more rapid sequence will drain it faster than letting it rest for a time between power usage. At least that's my impression of how it goes. I usually figure an 18650 will get me through about 5-6mls of juice. An 18490 will get me through 3-4 mls, and an 18350 or 14500 will give me 2-3mls per charge. Depending on device, and whether regulated or not, these figures have some wiggle room, but in my estimation, that is about what I get from the different cells. I pull my batteries as soon as they start blinking, never run them to full cutoff. And if running a mech, I pull them as soon a vapor diminishes, which is usually about 3.7-3.8 volts resting voltage.
Well here are the Provaris... Some of them...
Hey @zen ... How often you clean the threads and no-lox ... weekly? monthly?
Sent via iPhone
Must be like painting the Golden Gate Bridge.
By the time you get to the end it's time to start over.
I do love Zen's collection ... it's like one of those ... really? that can't be real
Sent via iPhone
Sent via iPhone
Just stuck the Radius on the charger.
Left the screen on so I could see what it does.
Screen turned off, but if you punch the button it shows a little lightning bolt in the charge box.
I like that. Doesn't need to stay lit for me anyway.
I don't think I saw that with the display off.
Gonna check that.
Left the screen on so I could see what it does.
Screen turned off, but if you punch the button it shows a little lightning bolt in the charge box.
I like that. Doesn't need to stay lit for me anyway.
I don't think I saw that with the display off.
Gonna check that.
Hey @zen ... How often you clean the threads and no-lox ... weekly? monthly?
Noalox... I NEVER put Noalox on a stainless Steel device... It's specifically designed for Aluminum. The correct thing to put on Stainless is Sanchem No-Ox-Id "A" Special... and generally, For the shelf queens I put it on when I get them and never do it again. For ones that I use they get it when I notice something is behaving badly. I'm not on a maintainence schedule with these things... they just keep working and I don't think about it much.
I do love Zen's collection ... it's like one of those ... really? that can't be real
Oh... it be real... it be very real.
Okay, after using it for several days:
1. For some odd reason, all my tanks seem to sit flush on the 510 even though the 510 is not spring loaded. Some people won't like that but i'm sure Provape did it on purpose so its stays 100% sealed against any juices leaking inside the mod. And i'm perfectly fine with a fixed pin cause I trust Provape
2. No more noalox!!!!!!!! I HATED how gritty the 2.5 provari would get after time and had to constantly clean out the old noalox and apply a new paste just to get it even somewhat smooth, those days are long gone, thank god!
1. For some odd reason, all my tanks seem to sit flush on the 510 even though the 510 is not spring loaded. Some people won't like that but i'm sure Provape did it on purpose so its stays 100% sealed against any juices leaking inside the mod. And i'm perfectly fine with a fixed pin cause I trust Provape
2. No more noalox!!!!!!!! I HATED how gritty the 2.5 provari would get after time and had to constantly clean out the old noalox and apply a new paste just to get it even somewhat smooth, those days are long gone, thank god!
I just use the DeoxIT Red cleaner.
It leaves a little film for protection without gunking everything up.
It leaves a little film for protection without gunking everything up.
Last edited:
I was just going to live with it, till someone mentioned you may want to know
Sent from my LGMS631 using Tapatalk
I made it to tank 6 (kabuki) Before it died (suddenly, since battery bar still said full up to then [emoji14])
Sent from my LGMS631 using Tapatalk
Oh, and that was at 14 watts boost 4
Sent from my LGMS631 using Tapatalk
Sent from my LGMS631 using Tapatalk
It''s not really a fixed pin, it has some "give" to it. But it's not spring loaded either. Kind of a cool solution.
Thank you, 'Brow.
Oh you -- who ............... @Pinggolfer, @rbrylawski, @Bronze, @DPLongo22, @WillyZee, @ENAUD, @jwbnyc, @The Ocelot, @raitizz @AstroTurf, @LittleBird, @Peter_C, @ ...... (and anyone else I may have forgotten)
It's LUBE talk time.
Last edited:
They always want to know. I imagine even if the problem is from user error, or even dropped, it's something they might keep in mind when designing a new product and choosing the component materials.
Oh you -- who ............... @Pinggolfer, @rbrylawski, @Bronze, @DPLongo22, @WillyZee, @ENAUD, @jwbnyc, @The Ocelot, @raitizz ...... (and anyone else I may have forgotten)
It's LUBE talk time.
Of course it is! It hasn't been discussed on this thread and there are folks who haven't visited the first part of the P3 thread. They must be enlightened!
No-Ox for the win!
- Status
Similar threads
