________O you flatlined the ish out my ...!!!
I'm laughing so damn hard I KNOW my neighbors have got to hear me.
:/tears!!!!!dibster my screw came today.
PDIB's Making MODs!
- Thread starter pdib
- Start date
- th_trl_thread_readers 0
- Status
________O you flatlined the ish out my ...!!!
I'm laughing so damn hard I KNOW my neighbors have got to hear me.
:/tears!!!!!dibster my screw came today.
Wish I had seen this before you went all HULK SMASH!!! On your atty Lex. I actually made an extractor for my brass caps + brass drip tips some time ago...
1) Take a piece of wood that is about 0.5" thicker than your tip is long.
2) Drill a hole into it that is just a hair wider than the tip.
3) place tip down into hole so that cap rests upside-down on the wood.
4) find a drill bit that is a hair smaller in diameter than the drip tip and place the non-cutting end flat against the bottom of the tip.
5) tap drill bit lightly with a hammer, wooden spoon or rock... Avoid using muffins or glassware
6) pick up wood and retrieve tip from hole
I have about 1000000001 "just the tip" jokes right now, but i'll spare you!
Sent from the zoo using Tapatypo 2
1) Take a piece of wood that is about 0.5" thicker than your tip is long.
2) Drill a hole into it that is just a hair wider than the tip.
3) place tip down into hole so that cap rests upside-down on the wood.
4) find a drill bit that is a hair smaller in diameter than the drip tip and place the non-cutting end flat against the bottom of the tip.
5) tap drill bit lightly with a hammer, wooden spoon or rock... Avoid using muffins or glassware
6) pick up wood and retrieve tip from hole
I have about 1000000001 "just the tip" jokes right now, but i'll spare you!
Sent from the zoo using Tapatypo 2
Monkey I think you'll have to build it for her. I don't see her drilling wood or tapping or anything...
Thanks for the recipe Bore! I mixed up a 30ml batch and all I can say is "Holy Flavor Batman!" It's very good, right up my ally i love fruit flavors, but like you I also use MM wire. I guess I didnt realize how little flavoring I was using for my watermelon melon blend (3-5% total) 8% of each was a little much for me
. I'm running .55ohm MM with RxW. Time to recoil and up my resistance, because you know any excuse to recoil 
. Did I hear somebody right... Does Gigdujour have a special apple pie DIY flavor?
I'm glad you like it! Did you let it steep any? I normally run my MM at around 1 ohm even-ish.
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
Monkey I think you'll have to build it for her. I don't see her drilling wood or tapping or anything...
All this misses the fact that she took care of business.
Good point pdib - looks like blossoming "MODDERS" to me. The large C clamp should be in everyone's kit!
Is that what this thing is called?Good point pdib - looks like blossoming "MODDERS" to me. The large C clamp should be in everyone's kit!
No seriously........I don't even know where it came from.
C-Clamps are for people who don't have a bench vise.
correction: C clamps are for people who don't have nippoh clamps
Ahem, if you had a D clamp, the correct answer would be that you'd never be able to raise your D
Sent from my iPhone using Tapatalk
So the Simian took it's first fall today.... Stupid thumbless paws! About a 3' drop, didn't come apart and not a scratch on it. I freaked! It was all happening in slow motion!
Thank Jeebus it didn't break. I would have been one sad primate.
In other news... Giggy sent me some of this Hg whatever cotton... Do you guys separate the pad and pick the fluff from the middle, or cut a strip off the pad and roll it as-is?
I've always used cotton balls, never pads....
Sent from the zoo using Tapatypo 2
Thank Jeebus it didn't break. I would have been one sad primate.
In other news... Giggy sent me some of this Hg whatever cotton... Do you guys separate the pad and pick the fluff from the middle, or cut a strip off the pad and roll it as-is?
I've always used cotton balls, never pads....
Sent from the zoo using Tapatypo 2
Glad it survived the fall! pdib's list must be pretty long by now, but you would have to wait millennia for a replacement.
I open the pad like a book to separate it into two halves, then cut strips along the fiber grain. Don't know about any fluff, but I am using KGD if that's different from Hg whatever. I think pdib has a pictorial somewhere around ECF, but I don't know where it is.
- Status
Similar threads
