Penelope V2
- Thread starter imeothanasis
- Start date
- th_trl_thread_readers 0
- Status
It depaned on coil and setup.
I think the opposite,
if the setup work good with bigger air hole it vape more.
Maybe if you are using MP it reduce it a bit?
Now after I set it with the 2x 3mm wick and open drip tip,she steam big fluffy clouds,
With no harshness.
Of course depends on coil and setup
I used all controls-fully open (100 percent vg )
I use the same setup to ithaka
I have nothing to measure it (broke my EVIC
) but this is my setup 2x 3mm wick x 3 laps .5 ribbon
does not matter so much anyway I bought my 500 ml base
I used all controls-fully open (100 percent vg )
I use the same setup to ithaka
I have nothing to measure it (broke my EVIC
does not matter so much anyway I bought my 500 ml base
Last edited:
The wick on Itahka is made
By 4 channels,so coil maybe more saturate on Ithaka.
But as I said in previus post,if you compensate,
With double 3mm then all is fine.
The channel is also deeper I think (it look like that to me),and that's do provide
Better wicking.
Actually it wick great,never thought it can be with one channel,but it is.
By 4 channels,so coil maybe more saturate on Ithaka.
But as I said in previus post,if you compensate,
With double 3mm then all is fine.
The channel is also deeper I think (it look like that to me),and that's do provide
Better wicking.
Actually it wick great,never thought it can be with one channel,but it is.
Just A question. The tank section of the penelopeV2 does it has the same dimensions of the old penny?
I was thinking about this statement Imeo and I am wondering. What is the distance between the 510 connector and the 5 partial air slots on Penelope's base?
I found and edit some photos from a nice but in spanish language video...
just to see some differences between Penelope V1 and V2
just to see some differences between Penelope V1 and V2
Ok now after more time of vaping miss Penne',
We notice the draw on the JGG CT with the 510 lid is better,and
In a way with the air comming direct from below it help
To achive better wicking??
Strange but it does fill like so.
It like a bit of closing the AR provide better pull to the juice in the channel.
Few more vape.
And yes it does!
So if one working with regular drip tip
it's better on JGG CT with the 510 lid,so far.
We notice the draw on the JGG CT with the 510 lid is better,and
In a way with the air comming direct from below it help
To achive better wicking??
Strange but it does fill like so.
It like a bit of closing the AR provide better pull to the juice in the channel.
Few more vape.
And yes it does!
So if one working with regular drip tip
it's better on JGG CT with the 510 lid,so far.
Just out of curiosity. Did they post the V2 with or without stock? It says they are sold out. Not that it matters (to me) because I'm still waiting on my Preorder in the U.S.
I just placed the penny on a flat top mod. It's vaping well. I feel airflow. It may be a tad held back but if I had to vape it like this for a day or more I could.
.
Yeah I asked because I am thinking with some mods at least it would likely work. Especially if it's 510 connector had the little air slots in it. Good to know it can work
great comparison Stelios
I found and edit some photos from a nice but in spanish language video...
just to see some differences between Penelope V1 and V2
then it will work fright. But there is no way for a flat connector mod to work with any atomizer without those slots on its cap. Exept a mod breaths from somewhere else
Last edited:
is it totally flat yankee? Then how atomizers breath?
This is the cap I used with the Penelope.
- Status
