ProChat - All Things ProVape and Beyond
- Thread starter rbrylawski
- Start date
- th_trl_thread_readers 0
- Status
I have another Provari on the way. I needed that like a hole in the head but it is what it is. I should have gotten the ones I have properly outfitted first. I am going to send one of my babies off for surgery and didn't want to only have two on the desk while it is gone. I wouldn't have one to put in my pocket either since it is the mini that will get sent of for surgery.
Last edited:
The build deck on a KFL is HUGE compared to a Sophia.
I love the Sophia V2 and am still getting another one. I did want to keep all my toppers the same but I think the mini can justify being different than the desktop Provari.
I am going to retain plug and play with cartomizers, The Sophia is playing in a huge tank and so will the second one. The Mini is going to become a convertable, it will get tubed and topped for desk duty then retubed and topped for pocket duty. With the RBA's I will be ready in case hardware is hard to get.
I am going to go into juice supply stocking mode heavily as soon as hardware is sorted.
I am going to have all the bases covered except for my unicorn.
I broke down and have another mini coming since I didn't want to be without one when it goes into surgery. I will have a backup for surviving the long term if the FDA hits us hard.
Last edited:
A good Vision Nova setup still rocks the ProVari, for me at least! 19mm of bliss on top of the slant cap.
Now if they had just made a Ti version to go with my 2.5...
Hmmm, where Provari originally made slant cap because of 19mm toppers? Makes sense if it was.
Question for Kayfun users: I have two style of Kayfuns, the one pictured on a mechanical below:
And the older style with the rounded tip, like this:
They both vape the same, as far as I can tell, the difference being the drip tips. Both drip tips are 510, but both also fit in a "knob" permanently attached to the flat part of the cap. Are all Kayfun-like styles shaped that way or are there some where the drip tip sits flush on the flat top (like on the Rüzgar pictured on top of my full-sized Stealth)?
And the older style with the rounded tip, like this:
They both vape the same, as far as I can tell, the difference being the drip tips. Both drip tips are 510, but both also fit in a "knob" permanently attached to the flat part of the cap. Are all Kayfun-like styles shaped that way or are there some where the drip tip sits flush on the flat top (like on the Rüzgar pictured on top of my full-sized Stealth)?
Last edited:
There were very few (if any) 22mm toppers back when the Provaris first came out. The beveled top caps were perfect in the day. With all these larger attys these days they look dopey on those beveled Provaris. Hence the explosion in beauty ring sales...which were slightly less dopey than being without it.
It does look a bit dopey but at least it doesn't effect performance. I will get one of mine altered but the rest are going to stay sloped.
Last edited:
All my top caps have the raised knobs on them. I have a couple/few nano styles with top caps and they are tiered as well. None are flush/flat.Question for Kayfun users: I have two style of Kayfuns, the one pictures on a mechanical pictured below:
And the older style with the rounded tip, like this:
They both vape the same, as far as I can tell, the difference being the drip tips. Both drip tips are 510, but both also fit in a "knob" permanently attached to the flat part of the cap. Are all Kayfun-like styles shaped that way or are there some where the drip tip sits flush on the flat top (like on the Rüzgar pictured on top of my full-sized Stealth)?
You can always get beauty rings from ProVape. I recently had my old P2 in for repairs and I had them convert it to a P3 top cap. Like it MUCH better.
- Status
Similar threads
- Locked
