Reload Rta

Status
Not open for further replies.

benley73

Ultra Member
ECF Veteran
May 2, 2016
1,382
2,219
52
Thanks for all the pics & your assurance!
Have a look over the ECF forum for the Coppervapes BF , lots of info on there ,
On fasttech they have v1 kit or v2 the mod is now V2 so get v2 kit , works a lot better with your own rda than the Included one , its a really solid built mech practically nothing to go wrong ,
You can adjust the 510 up and down via 2 small holes under once the 510 BF pin is removed ,

Sent from my ONEPLUS A3003 using Tapatalk
 
  • Like
Reactions: Heartsdelight

Heartsdelight

Vaping Master
ECF Veteran
Nov 10, 2015
5,777
19,659
Have a look over the ECF forum for the Coppervapes BF , lots of info on there ,
On fasttech they have v1 kit or v2 the mod is now V2 so get v2 kit , works a lot better with your own RDA than the Included one , its a really solid built mech practically nothing to go wrong ,
You can adjust the 510 up and down via 2 small holes under once the 510 BF pin is removed ,

Sent from my ONEPLUS A3003 using Tapatalk
I'm reading the thread now lol! You're not kidding 105 pages. So if you unscrew the 510 bf pin from the bottom or top? Then there are 2 small holes that you can adjust with a tiny screwdriver?

Edit: I only ordered the mod. Will use the Pulse bf rda, I also won a Serpent bf rda & just ordered the Gaia bf rdta.
 

Fictitious Character

Ultra Member
ECF Veteran
Verified Member
Aug 24, 2014
1,002
553
USA
I went completely overboard now. Originally I wanted to buy the missing gold authentic one, now ended up buying all 3 kindbright clones and one non-kindbright to compare (and I wanted them all to be kindbright). 6 reloads... should last me a bit (or I will give some away :D). So lots of comparisons coming in.. auth vs. clone... clone vs. clone...
Haha I went over board with this too. I bought two black ones to compare to the authentic and finally got shipping notice a couple days ago. They look to be in NY currently. And then last night I ordered the SS and the gold. Now I see all are out of stock. Hoping I am not going to get an email refunding my order.
Funny thing is I didn't even really want a gold one as I was going there for a Sherman clone but hit the Reloads again instead.
 

benley73

Ultra Member
ECF Veteran
May 2, 2016
1,382
2,219
52
I'm reading the thread now lol! You're not kidding 105 pages. So if you unscrew the 510 bf pin from the bottom or top? Then there are 2 small holes that you can adjust with a tiny screwdriver?

Edit: I only ordered the mod. Will use the Pulse bf rda, I also won a Serpent bf rda & just ordered the Gaia bf rdta.
There is 2 holes under the 510,
You remove the fire button screw remove the copper spring , remove, the 510 Sqounker pin.+ Insulator ect , and then there are the 2 holes under the Actual threaded 510, allowing you to use a tool for grip it can be wound down or up depending on length of your RDA pin,
to allow atties to sit flush.
Or short ones to make a good connection.
Rest is maintainance and such theres little too it. Not much to go wrong being a mech its built to last a very long time.

Sent from my ONEPLUS A3003 using Tapatalk
 
Last edited:

Heartsdelight

Vaping Master
ECF Veteran
Nov 10, 2015
5,777
19,659
There is 2 holes under the 510,
You remove the fire button screw remove the copper spring , remove, the 510 Sqounker pin.+ Insulator ect , and then there are the 2 holes under the Actual threaded 510, allowing you to use a tool for grip it can be wound down or up depending on length of your RDA pin,
to allow atties to sit flush.
Or short ones to make a good connection.
Rest is maintainance and such theres little too it. Not much to go wrong being a mech its built to last a very long time.

Sent from my ONEPLUS A3003 using Tapatalk
Thanks Benley!
 

BlackCRX

Senior Member
ECF Veteran
Feb 20, 2014
210
266
Vancouver Canada
Just got my clone reload from 3F this morning and got around to cleaning/building/vaping.

Vape is flavorful and warm with a 3mm ID dual 26 SS plain round coil at 450F. Better than the Engine dual coil IMO.

Things to note:
-The barrel/chimney "looks" dirty, but after a couple of washes and scrub with isoproypl alcohol plus a couple more rinses... looks just as dirty as before. I'm guessing it is just poor quality stainless or bad polishing.
- Do not tighten your leads all the way if you are using regular round wire (26 gauge in my case), it will cut the wire. Just tighten it until it is snug, insert your coil rod and give it a gentle tug, if it doesn't pop out, you're good. I had to make new coils because I always like to tighten them... or over tighten them.
-When wicking, make sure the wicks touch the bottom of the juice channel. I originally had mine just half way in the juice channel or half exposed in the juice "window" and within a few minutes it leaked everywhere. I re wicked it now with the wicks touching the bottom of the channel and fully covering the "window" and no leaks so far.
-Watch out for the top cap when you open to fill or disassemble to clean. The machine is really sharp. When vaping, keep note so you don't cut or scratch your lips.

Only used it for an hour, but so far it has been a pretty good vape.
 

Heartsdelight

Vaping Master
ECF Veteran
Nov 10, 2015
5,777
19,659
Just got my clone reload from 3F this morning and got around to cleaning/building/vaping.

Vape is flavorful and warm with a 3mm ID dual 26 SS plain round coil at 450F. Better than the Engine dual coil IMO.

Things to note:
-The barrel/chimney "looks" dirty, but after a couple of washes and scrub with isoproypl alcohol plus a couple more rinses... looks just as dirty as before. I'm guessing it is just poor quality stainless or bad polishing.
- Do not tighten your leads all the way if you are using regular round wire (26 gauge in my case), it will cut the wire. Just tighten it until it is snug, insert your coil rod and give it a gentle tug, if it doesn't pop out, you're good. I had to make new coils because I always like to tighten them... or over tighten them.
-When wicking, make sure the wicks touch the bottom of the juice channel. I originally had mine just half way in the juice channel or half exposed in the juice "window" and within a few minutes it leaked everywhere. I re wicked it now with the wicks touching the bottom of the channel and fully covering the "window" and no leaks so far.
-Watch out for the top cap when you open to fill or disassemble to clean. The machine is really sharp. When vaping, keep note so you don't cut or scratch your lips.

Only used it for an hour, but so far it has been a pretty good vape.
Hey how did u get it so fast? What color did u get? Happy you like it!
 
  • Like
Reactions: franck

BlackCRX

Senior Member
ECF Veteran
Feb 20, 2014
210
266
Vancouver Canada
Hey how did u get it so fast? What color did u get? Happy you like it!
I originally ordered the black one, but shortly after they had the stainless one on at 24hr ship so I cancelled the black and ordered the SS.
Ordered on June 1st, shipped on June 3rd, arrived today in Canada
 

BlackCRX

Senior Member
ECF Veteran
Feb 20, 2014
210
266
Vancouver Canada
That was fast! Enjoy it for us :cool: :D
So far so good. I vaped 2 different juices that I made that is in my average rotation so I know what it is suppose to taste like. Right up there with some of my favorite tanks.
I might play with the coil placement later on. Right not I have it sitting right on top of the airflow, almost parallel to the moon shaped cutouts. But when I look down from the chimney I see there is still quite a bit of space between the coil and the top of the chimney. I might move it up a little, but at the same time I don't it too high as it would block air flow from wrapping around the coil and up the coil from the outside.

Also another note, the airflow draw is really loose. I have it closed off to about 1/8 open to get the restrictiveness that I like
 

Heartsdelight

Vaping Master
ECF Veteran
Nov 10, 2015
5,777
19,659
IMG_0335.JPG
Just checked my tracking, surprised my ss was in New York last night! Soon I shall have it!
 
Status
Not open for further replies.

Users who are viewing this thread