Reload Rta

[BartH33]

Thx for the reply but it seems unlikely.
I tried a lot of cotton and toned it down to the point of leaking even tried different brands of cotton. I also have an ammit dual and it has more flavor but needs more cotton. I even played around with the height of cotton in the JFC. The wicking is super fast because I see bubbles from the moment I take a puff.

 

[fifamymaingame]

The wicking on this has to be 100 to little get spit back to much no flavor haha noticed even with not enough cotton I get bad flavor too

 

[BartH33]

I really had the feeling I tried it all. What is your 100% right wicking? I know this is a difficult question but I use 3mm coils. My cotton is snug but movable in the coil. My ends are really thinned to improve wicking and definitely not stuffed. I comb them out pretty far.

 

[fifamymaingame]

I haven't done a 100% yet haha I'm having hard time getting the right amount in wicking channels it's either not enough or to much my coils aren't directly over the air flow just close enough

 

[BartH33]

Funny, you have problem with wicking channel I have problem with coil wicking and not the channel. For me the trick for perfect wicking was to move the cotton to the outer sides and make a small air hole in the center of the juice flow channel down to the juice flow port so that air can escape. My cotton is pretty losse in the JFC and have zero leaking. Tomorrow I am going to try ss flat Clapton wire and cotton bacon. I normally use kendo gold but maybe bacon is better for this rta

 

[fifamymaingame]

I just don't know where to cut the cotton I've tried alot with this thing to find the right length tried lining up just outside the o ring and feels to much

 

[fifamymaingame]

My flavor feels dropped no matter how many times I wick could be my tounge tho

 

[BartH33]

So I tried a single coil flat Clapton 4mm and flavor was much better. Resistance was 0.18 5 wraps fitted just in the chamber. So it must be something with the coil placement. I think the cotton length is perfect when you cut just above the bottom o ring but you need to fluff the cotton up quite a bit. It needs to be loose in the JFC but only just.

 

[fifamymaingame]

Just above ok I'll try that I can't even see cotton when I put it all back together no leaking but still finding where to cut or how fluffy to make it's been a hassle gotta get another bag of wick when I pick up some 0.4 fused claptons

 

[fifamymaingame]

After 20 wicks I think I get it now just made the wick in the coil super loose and cut it at the bottom of the base where the 510 is fluffed it now I can finally see cotton when I throw it all back together now to figure why I feel like I got no flavor

 

[divy]

I just got the reload clone....it pretty much leaks the whole tank through the AFC every time..i wick it with a single coil but i make sure theres enough cotton to cover the whole wicking chamber/juice vents...any suggestions.

 

[fifamymaingame]

I remember hearing the o ring on the clone deck is flimsy all I can think off

 

[AnthonyB]

Has to be your wicking

I too been struggling to get it right either to thin and short so I can barely get any cotton in there or I use to much I can't figure out where to cut the lengths sometimes

I've had all kinds of trouble with my Reload but it is one RTA that I feel is worth it because when I get it right it Vapes as good as anything I've ever vaped.

There is definitely a learning curve with using postless decks. I sometimes don't cut the legs of the coils to be perfectly even with each other.

I often get the wicking wrong too. I've had too little wicking resulting in leaking and too much wicking resulting in dry hot hits. I find that the wicking is perfect for me when the juice pops a bit when firing.

I've not yet been able to build a coil so well that I can hit the Reload multiple times in a short time period without getting a bit of a dry hit.

The worst problem I had was the grub screws. The installed grub screws seemed to not tighten down properly and behaved like screws that were partially stripped. It caused a lot of shorting.

I found that disappointing on a mod of this price and fame. I was forced to use 3 of the spare grub screws and thankfully that solved the shorting problem.


Sent from my iPhone using Tapatalk

 

[fifamymaingame]

Yeah wicking is the hardest part for me I wish there was a lengthy detailed tutorials how many mms to cut the coils how much mm the cotton needs to be

I wanna switch to rayon

They told me soon they will have spare parts

 

[ianblankg]

After 20 wicks I think I get it now just made the wick in the coil super loose and cut it at the bottom of the base where the 510 is fluffed it now I can finally see cotton when I throw it all back together now to figure why I feel like I got no flavor

Flavor has to do with how the air flows around your coils so coil placement is where you need to focus. Not too high and not to close to the deck. I guess maybe a bit closer to the deck than the top. Imagine 2 straight lines from the 2 side air holes directly to the chimney and you want the airflow to hit on the top half of the coil. I use a 6 core 32g spaced kanthal on mine and the flavor and clouds are perfect.

 

[fifamymaingame]

Flavor has to do with how the air flows around your coils so coil placement is where you need to focus. Not too high and not to close to the deck. I guess maybe a bit closer to the deck than the top. Imagine 2 straight lines from the 2 side air holes directly to the chimney and you want the airflow to hit on the top half of the coil. I use a 6 core 32g spaced kanthal on mine and the flavor and clouds are perfect.

Where I'm at now still don't feel I'm getting good flavor every one tells me it tastes great but to me everything just a subtle flavor

 

[fifamymaingame]

Another shot

 

[ianblankg]

Where I'm at now still don't feel I'm getting good flavor every one tells me it tastes great but to me everything just a subtle flavor

Those are too close to the base. You can try just bending them closer to each other. They are too close to the holes. From the top down you want to line it up with the square shape of the deck. If that doesn't work, what I'd do is get something metal that's a slightly smaller diameter, heat up the coils then insert the metal and lift, kind of teeter totter, until it shrinks the diameter of the coil, raising it up a bit higher from the base. That's how I do all my builds, I build a diameter a bit bigger than I want, install them touching the base and do that technique to raise them up enough.

 

[fifamymaingame]

I've had them higher and it was worse had a dude who does 200 builds a day do the reload for me and I cut them exactly as the last build he did

Every reload video said to push them as close to the curved air flow as possible

Now sure what method your talking about I'd have to see a video

 

[ianblankg]

I've had them higher and it was worse had a dude who does 200 builds a day do the reload for me and I cut them exactly as the last build he did

Every reload video said to push them as close to the curved air flow as possible

Now sure what method your talking about I'd have to see a video

Like this pic, also do you vape the same ejuice all the time? If so it could be vapers tongue. But try like in the pic, that far off the deck. You don't want them too high either, there's a sweet spot. Definitely move the coils closer to each other, away from the holes a little bit, like in my pic