- Status
Well if it is a DNA60 board and you don't have EScribe to connect it up to a PC, it might be in Stealth mode.
Click the fire button 5 clicks. Now it shouldn't fire because it is in lock mode. While in lock mode, press the fire and down buttons for 5 seconds. That will switch it to normal mode. If no screen, I'd do it again because it must be something else and now it is in Stealth mode. So again will take it back top normal mode. It is still locked, so 5 fire button presses and it should fire once again.
Also, the screen might be bad. The ones for the DNA 60 can be had for under 10 bucks and are relatively easy to replace. Just a small Molex type ribbon socket.
OK. I didn't have much luck with the STM insert. Don't feel like spending a lot of time figuring it out since my Xeta is on the way. Today I set it up with the Nautilus coil head and it's great. Doubt if I'll use that much because I need to keep those coils for the wife's Nautilus but it's nice to have the BB doing something good.
Did learn one lesson today. When I put it together with the Nautilus head I managed to leave it with the glass door not all the way closed. Maybe just 1/16th short but enough for it to leak a bit at the top and the bottom. Luckily I opened it to change the power and noticed before it got too wet.
Did learn one lesson today. When I put it together with the Nautilus head I managed to leave it with the glass door not all the way closed. Maybe just 1/16th short but enough for it to leak a bit at the top and the bottom. Luckily I opened it to change the power and noticed before it got too wet.
Sxk board. I heard it's an Asmodus board. Not sure myself and followed some advice I got on that board. It didn't work.
The one I got don't have a usb either. It's not the newer version with usb port.
Thanks for replies.
Thanks for replies.
I have opened the BB. The mod still fires but the screen is still blank. Might be the screen that's just bad. There was no juice inside so it can't be moisture.
I haven't used it in a while due to this but I think I'll use it as is after a pitstop. Having the screen work is just a bonus.
I haven't used it in a while due to this but I think I'll use it as is after a pitstop. Having the screen work is just a bonus.
2F seems to be the fastest shipping right now. Only took 3 weeks from order to escaping customs yesterday. My FT and 3F have been in limbo for a month and a half
I'm surprised the 2F stuff is taking that long,which shipping method did you use?I made 2 orders with them last month,each time i paid i think about $5 for shipping.The first order from time of order to hitting my mailbox was 6 days,the 2nd order took just shy of 2 weeks from order to mailbox.
I can thank ISC. It sat there for over a week and a half. Considering I’m only consistently getting mail delivery about 3 days a week right now, customs is just the first bump in the road here.
Gas City got in a new shipment, so I ordered a red BB.( Red and black are all they have in stock )
It’s coming UPS, so it should be here quickly. I’m just sitting here with a backhoe digging a deeper rabbit hole
.
I broke the positive post on my first Xeta - an SXK. I bought a YFTK version and discovered that there is about 0.5mm more room for the coil between the posts so 3mm id coils fit better. I've also found that the chimney section has a sturdier O ring on the SXK. The YFTK was spinning inside the Boro when I screwed down the 510 key so the best combo for me is the YFTK deck and barrel with the SXK chimney.
Here's a comparison of the 2 decks:
Yes - pretty sure its an Asmodus GX80 board
That's very good. When I was comparing mine a few months ago all I did was look for the rounded off points on the clamps to see if they cloned the prototype or the production version.
They must use different o-rings as they are available though or something because the tension between the chimney and the barrel is the same on my YFTK and SXK.
That's interesting - manufacture runs maybe. My YFTK chimney o ring even looks a bit thinner than the SXK. First thing I noticed when I unpacked it and had a look at the 2.
Also it was great to get a spare pos post with the YFTK cause even though I was aware of it (having snapped my SXK post) I still managed to crack it on my first build. It's holding together and coil resistance looks good but it won't last more than a few builds
Yours both look thicker than all my YFTK's, here's a couple of the spares, not far off being paper thin...
Actually, one is 0.17mm the other 0.2mm, paper is 0.1mm thick, lol
Got the vapesnail in the mail today. I set it up without the inserts and its a bit airy but great vapor production. I need to know what insert to use, and where to place it to get more juice suction in the chamber? I dont want to vape mtl, I just want to create a semi restricted dl vape with more juice flow. I cant use less wicking because that will flood the chamber.
Sent from my SM-G950U1 using Tapatalk
Sent from my SM-G950U1 using Tapatalk
I ordered the full kit today. Along with a Bridg'd and a third Xeta. Excited to see how it is.Got the vapesnail in the mail today. I set it up without the inserts and its a bit airy but great vapor production. I need to know what insert to use, and where to place it to get more juice suction in the chamber? I dont want to vape mtl, I just want to create a semi restricted dl vape with more juice flow. I cant use less wicking because that will flood the chamber.
My snail should be here in a few days,it's in Kentucky now,so probably have it Monday or so,but very interested in trying it out.I only got the basic one without the inserts though,and a spare tank section.I plan to order the Bridg'd and Krma as well,but i caved and bought the red SXK today,so those atty's will have to wait a while now haha.
- Status
