SXmini M Class (TEMP CONTROL)
- Thread starter whitewidows
- Start date
- th_trl_thread_readers 0
- Status
Yep you have a point. All I am saying is if you do build a low ohm coil you don't need the high J setting. Like I said everyone is different and that's what makes vaping fun. If thats what you like then that's great. Oh and by the way if you wear a hat no one will notice that point. LOL just joking around.
I use 50/50 and the flavor I use is only 2% also 2.5mg nic
Last edited:
I asked YiHi: "If the device and atomizer is at the same temperature, will the temperature control always work correctly even if they are not at room temperature? For example, if I’m outside in near-freezing weather, will it still work properly or do I need to adjust my temperate limits by how much I’m off from room temperature?"
Yihi's Response: "If the outdoor temperature is very low, as you said if freezing weather, preheat is necessary, otherwise it cannot work well."
Not the perfect answer, but it's enough I think to conclude that the SXM assumes room temperature conditions when setting resistance.
Yihi's Response: "If the outdoor temperature is very low, as you said if freezing weather, preheat is necessary, otherwise it cannot work well."
Not the perfect answer, but it's enough I think to conclude that the SXM assumes room temperature conditions when setting resistance.
That would explain much, that's pretty watery and lightly flavored. I use 80-100% VG, because I greatly dislike PG. 50/50 gags me.
I am still wondering if the Jwraps will work on my black one that I got. It was the second batch and it has a rough finish not smooth like my grey or I think the older blacks.
Finish shouldn't matter, the J-wraps will adhere just fine. That 3M adhesive is good stuff.
Cool IDK if this is their answer to the problem of the finish or not. It seems to be holding up well in the 10 days that I have had it so does the grey which is older. But those carbon fiber J wraps are pretty cool too.
Heres something I was wondering. I bought a box of the NI200 heads for the STM but I didn't like them in my rDNA40 but I've been hearing they work well on the SX. Since they are .15 what temp and J settings are you using with them. Thought I might give one a try just to see.
I opted to keep my device as my local B&M only had a device which was built on the same day as the one that lost all its paint (March 27th) - ended up with vapor skinz- not impressed that it comes in 2 pieces which causes a seam in the middle or that the sticker goes all the way to the edge instead of leaving the frame exposed - I may trim it back with an xacto knife.
Attachments
Has anyone gotten one from Jwraps are they 2 piece or a single piece. I think I saw one and it looked pretty good. Was thinking of the carbon fiber. Any cutting on them or are they better. I think I saw a pic but don't know how I would find it again. May check YouTube. One of the reviewers I watched today was going to put one on and have a video of it.
Take a hair dryer to that skin, heat it a bit and those lifting edges will smooth right out.
Carbon Fiber, three pieces, front piece not installed:
Sent from my iPhone using Tapatalk
I contacted the vendor about my bad black Mini. He said he would give me another but he only has grey left and that the Version 2 black Mini's will be shipped towards the end of May. He also said that is when the frosted Yihi sleeve would come out as well. Should I wait on the black or take the grey? Is the black that much more sexier then the grey?
Did that- they aren't lifting those are just shadows from the flash... trimmed the frame- View attachment 456339 - much better.
Attachments
Are you using a Ni200 build in that Mutation? And if so, what specs?
i can only get them to work well on dna40. all over the place on sx but others hava had some success i think. Not so pronounced in mini but crazy in nano. Anyway, give it a go!
Well I ordered 2 carbon fiber Jwraps black and grey same as my M's. They look like they go on pretty good but will have my wife do it.
- Status
