~The Billet Box~ page 1559 continued...
- Thread starter Doug Dino
- Start date
- th_trl_thread_readers 0
- Status
There are a lot of items out there for rev4. Very creative people. Look at this one, You can check your juice level. And change you watts.
But then, if you drop it. Your screen and tank aren't protected.
It kind of defeats the purpose in my mind, of what it was designed to do. Protect everything.
But it would look great on my coffee table. Never leaving the house. And it goes with my wife curtains.
There are a ton of options out there if you want to stalk FB in the super secret groups loaded with people looking to get on a randomizer - all to pay upwards of $200 for a set of doors. No thanks.
To find some on a website FOR SALE is amazing IMHO.
For anyone not familiar with vapesbyenushi, they seem to have access to some cool vape gear that only can be found on FB.
Really I see it on tapatalk and my Chrome browser.
You have me blocked HB?
Definitely not, my friend!
Well folks...I hate to be the bearer of bad news, but we've lost another one...
This is seriously sad.
If anyone knew Tim Brown, or purchased from him before/had contact with him, would you be able to reach out to him and see if he's ok?
I doubt something happened to HIM, but to see his site down is a bit disturbing.
For anyone who doesn't know about Serenity Gear, well...it was some of the first leather vape gear on the market, and some of the best.
This is seriously sad.
If anyone knew Tim Brown, or purchased from him before/had contact with him, would you be able to reach out to him and see if he's ok?
I doubt something happened to HIM, but to see his site down is a bit disturbing.
For anyone who doesn't know about Serenity Gear, well...it was some of the first leather vape gear on the market, and some of the best.
Well folks...I hate to be the bearer of bad news, but we've lost another one...
This is seriously sad.
If anyone knew Tim Brown, or purchased from him before/had contact with him, would you be able to reach out to him and see if he's ok?
I doubt something happened to HIM, but to see his site down is a bit disturbing.
For anyone who doesn't know about Serenity Gear, well...it was some of the first leather vape gear on the market, and some of the best.
Yeah I discovered that in December, the only contact I had for him was threw his website. I think he still had stock when he shut his site down, if I had known it was going to go away, I would have ordered a bunch of things.
KAS
Tim shut SG down quite some time ago. He sent an email blast (but I'm too lazy to search). I'm thinking it was around two years back (could be wrong). To jog your memory, we discussed it somewhat at length in the Provi threads, and it was even recently brought up again (by Duane).
Age - such a concept.
Here's the pic that Gnees posted too - not sure why some are having a problem seeing it. I obviously CAN see it.
Age - such a concept.
Here's the pic that Gnees posted too - not sure why some are having a problem seeing it. I obviously CAN see it.
I think it's getting 'round the time that I need to gas-up a "T'ree" (or two), and take 'em out for a spin.
I think it has something to do with what Ya' are posting the images with - no matter whether I am using Google on "My" computer or Android "Smart" phone, I can never see any of those images/smiley/emoticons when Tapatalk is used to post them . . . Just Sayin' . . .
It wasn't, Unc. Same as I always do (Chrome, drag & drop).I think it has something to do with what Ya' are posting the images with - no matter whether I am using Google on "My" computer or Android "Smart" phone, I can never see any of those images/smiley/emoticons when Tapatalk is used by anyone . . . Just Sayin' . . .
Sent from my SM-G935V using Tapatalk
Well then, I don't know what cause's it. . . Most of the time, I usually cannot see what images you post . . . NOT NICE
You neither? I figured it was an "Uncle" thing. Maybe I hadn't enough quotes, or animations... you know - something that makes sense.
But YOU?
Hi Raq.
I was thinking of you over the weekend. One of our esteemed (@gnees ) just ordered an Uno, and I almost recommended that he reach out to you. I recall that you were quite knowledgeable on the subject (and I definitely am NOT). I remember that you had some pretty good tips (to avoid leaking, etc,). I held up because I hadn't seen you in a while.
How ya doing? Everything going OK?
Or just point me to a page number. I'm up to 110 right now. A lot of battleship posts.
Esteemed?
Really?
~The Billet Box~ page 1559 continued...
Here is how I build mine:
1. On a 2.5mm bit I wrap 28g kanthal (26 is to thick so don't use it). I do 11 wraps which comes out to about 1.8'ish ohms for me.
2. Remove coil from the bit after wrapped and hold with tweezers. I fire up my handheld torch and heat the coil up applying slight pressure to the coil.
3. Put the bit back through the coil and insert the coil into the Uno base. The bit will help keep the coil in position. Run the rubber insulator over one leg and insert it into the base.
4. Pull both coil legs off to the side of the base and insert the pin.
5. Snip the coil legs as close to the base as you can
6. After assembled, remove the bit and use a screwdriver or something small to adjust the coils position so that it is centered in the Uno base.
7. Cotton it up. Use a lot of cotton and make it a tight fit in the coil.
8. Snip the cotton ends at the base. Leave a little extra outside the base and fluff the ends.
9. Adjust coil again and make sure it's centered in the base.
10. Juice up the coil and the ends of the cotton.
11. Screw the top portion of the Uno on.
12. Check to make sure the cotton ends are completely covering the Uno slats. If not, you will get leaking.
13. Once satisfied the cotton ends are covering the Uno slats completely, insert into BB tank and vape away!
The Uno comes with 2 small orings to adjust the draw. I find that using one oring does little to nothing but that adding both of them does tighten it up to where it's a tad / wee bit more airy than say the BVC's are.
Here is how I build mine:
1. On a 2.5mm bit I wrap 28g kanthal (26 is to thick so don't use it). I do 11 wraps which comes out to about 1.8'ish ohms for me.
2. Remove coil from the bit after wrapped and hold with tweezers. I fire up my handheld torch and heat the coil up applying slight pressure to the coil.
3. Put the bit back through the coil and insert the coil into the Uno base. The bit will help keep the coil in position. Run the rubber insulator over one leg and insert it into the base.
4. Pull both coil legs off to the side of the base and insert the pin.
5. Snip the coil legs as close to the base as you can
6. After assembled, remove the bit and use a screwdriver or something small to adjust the coils position so that it is centered in the Uno base.
7. Cotton it up. Use a lot of cotton and make it a tight fit in the coil.
8. Snip the cotton ends at the base. Leave a little extra outside the base and fluff the ends.
9. Adjust coil again and make sure it's centered in the base.
10. Juice up the coil and the ends of the cotton.
11. Screw the top portion of the Uno on.
12. Check to make sure the cotton ends are completely covering the Uno slats. If not, you will get leaking.
13. Once satisfied the cotton ends are covering the Uno slats completely, insert into BB tank and vape away!
The Uno comes with 2 small orings to adjust the draw. I find that using one oring does little to nothing but that adding both of them does tighten it up to where it's a tad / wee bit more airy than say the BVC's are.
~The Billet Box~ page 1559 continued...
Here is how I build mine:
1. On a 2.5mm bit I wrap 28g kanthal (26 is to thick so don't use it). I do 11 wraps which comes out to about 1.8'ish ohms for me.
2. Remove coil from the bit after wrapped and hold with tweezers. I fire up my handheld torch and heat the coil up applying slight pressure to the coil.
3. Put the bit back through the coil and insert the coil into the Uno base. The bit will help keep the coil in position. Run the rubber insulator over one leg and insert it into the base.
4. Pull both coil legs off to the side of the base and insert the pin.
5. Snip the coil legs as close to the base as you can
6. After assembled, remove the bit and use a screwdriver or something small to adjust the coils position so that it is centered in the Uno base.
7. Cotton it up. Use a lot of cotton and make it a tight fit in the coil.
8. Snip the cotton ends at the base. Leave a little extra outside the base and fluff the ends.
9. Adjust coil again and make sure it's centered in the base.
10. Juice up the coil and the ends of the cotton.
11. Screw the top portion of the Uno on.
12. Check to make sure the cotton ends are completely covering the Uno slats. If not, you will get leaking.
13. Once satisfied the cotton ends are covering the Uno slats completely, insert into BB tank and vape away!
The Uno comes with 2 small orings to adjust the draw. I find that using one oring does little to nothing but that adding both of them does tighten it up to where it's a tad / wee bit more airy than say the BVC's are.
THANKS, Raq - you ROQ!!!!
@gnees - you are NOT reading through ALL THAT STUFF. Are you????
- Status
Similar threads
- Locked
- Locked
