The kayfun conversion kit for terminator/nautilus

[Technonut]

Speaking of which, is there a place to get cheap tank sections for the term-c? Any clone parts, etc? It's sitting over there all lonely in SHORT mode while I enjoy the ithaFun and 91%..

Just pony-up the 20 bucks for one at Stormy's.... There are great deals for complete Term C's on the classies pretty often, but since you don't want to become verified, I know of no other place in the States to purchase separate tank sections. I purchased one at Stormy's myself before...

 

[Innocuous]

blech.. Well, that's next payday..

 

[dwcraig1]

Folks seem to like those big screw heads that secure the wire, I'm changing them for ones with smaller heads like on the kayfun.
I'll have to see if the ones in my KFL spares bag will fit next time I open the NF

 

[dwcraig1]

You guys didn't tell me that the drip tip mouthpiece telescopes, or did you?

 

[Innocuous]

HAH! I didn't even look at it closely! Another Vochu innovation and "gift"!

 

[Innocuous]

From the Vochu forum: <outside links are bad juju...>post892693.html#p892693

"As you probably noticed I closed the list. Due to many questions I have been sent regarding Upgrades availability I would like to inform you that the Upgrade will be available in Vapor-Freak.de very soon. Please check the site for updates"​

 

[dwcraig1]

From the Vochu forum: <outside links are bad juju...>post892693.html#p892693

"As you probably noticed I closed the list. Due to many questions I have been sent regarding Upgrades availability I would like to inform you that the Upgrade will be available in Vapor-Freak.de very soon. Please check the site for updates"​

I wonder how much they will cost from them

 

[Innocuous]

No idea.. Cheaper because he settles on machineshops and designs and mass-production? The same because he keeps a percentage?

Still an outstanding deal, mod and idea: turning chinee parts into useful new mods.

 

[hobbes4]

For those of you using this in the ithaka/hercules, make sure you use the 9x1.5mm o-ring inside the ithaka/hercules automatic juice feed. The o-ring that goes between the black plastic tube and where the conversion deck screws on. I mistakenly used the 9x2mm o-ring at first and my center pin was wobbly. Now that i have it correct no issues.

 

[dwcraig1]

I had some flooding/leaking issues, turns out the post wasn't tight enough in the main part. Due to the excitement I failed to check it prior to installation, I didn't clean this one either 'cause it smelled OK. I tighten it up and all is well again.

 

[dwcraig1]

So I decided to give dual micros with cotton a try, 8 wraps each side by side inline with the screws, came out to 0.5 Ω.
Using VG, liquid control is about half way.
The whole purpose was just to see if it could wick fast enough to keep up with these coils and it does well.
Now to put it back 'cause it's a bit much for the way I vape, I'd be nic'd out in a few with this.

Things are back to normal now.
I thought I'd try the extra screws that came in my KFL spares bag but all three were fill hole screws.

 

[upsetter21]

I just received my first Herc (bored w/ all else working so well & wanted to play along). The long center pin is not compatible with my modded center pin for MBK's. Not sure why these needed such a long post from the bottom other than for use on the 510 base. Haven't coil'd yet & already washed the little plastic ring down the drain. Complicated little beast.

To answer your quest 'bout the black plastic tube: seems to me it's a way to close up the "basic juice feed" assembly. Seems to me the large silicone ring goes to the base and the black plastic slips into basic feed with large black o-ring atop to effectively seal off the basic feed.

Also seems more tank sections are required to use this kayfun konversion in a herc. Still playing.

Well mine has finally arrived, simple enough to set up with a GGTS base as length isn't important.
The large black plastic sleeve I placed inside the GGTS base before screwing in the repairable part but really have no idea why I did that.
I didn't use an o-ring on the bottom of the stem as the lock nut isn't that close to the bottom of the base.

Anyone know what it's(the large black sleeve) for cause I may have put it in the wrong place?

It certainly works good, I put the same wick and coil and juice in it as I put in my KFL so to compare them.

 

[Innocuous]

Friends, Romans, Countrymen (and Greeks) - send me your herc's.. And term-c's..

<Innocuous makes plans to round the corners on the tank-section market...>

 

[gaijinrocker]

http://i.imgur.com/qkiDXD7.png
as u guys know..

Kit is available in Vapor-freak guys.

https://www.vapor-freak.de/Neu-im-Sortiment/Kayfun-Upgrade-Kit

 

[lumberjack]

Great price! Coupon code "FREAKY" takes 5% off.

I'm trying hard not to buy more. The Rampage large clear tanks are discounted, too.

 

[Innocuous]

Oh, thank the gods.. And Vochu.

 

[MacTechVpr]

http://i.imgur.com/qkiDXD7.png
as u guys know..

Kit is available in Vapor-freak guys.

https://www.vapor-freak.de/Neu-im-Sortiment/Kayfun-Upgrade-Kit

Great price! Coupon code "FREAKY" takes 5% off.

I'm trying hard not to buy more. The Rampage large clear tanks are discounted, too.

Oh, thank the gods.. And Vochu.

Would any of you gentlemen be able to school a newb on the intricacies of such an international retail order. I worked in logistics all my life but only know how to buy by the container or boat load.

Any feedback on credit card processing, how are exit taxes assed if any apply, duties on this end, does the c/c issuer manage transparently, etc. would be most appreciated.

Thanks in advance and good luck!

 

[dwcraig1]

So did everyone see the new rebuildable part to be offered by GG?
Have a look,

 

[Technonut]

So did everyone see the new rebuildable part to be offered by GG?
Have a look,

Too funny... I remember seeing Thanasis post in his forum regarding the Vochu kit when it first came out... He said there were no "upgrades" for his attys. If anything, the kit was a downgrade. Totally crapped on Vochu's idea.

 

[lumberjack]

Too funny... I remember seeing Thanasis post in his forum regarding the Vochu kit when it first came out... He said there were no "upgrades" for his attys. If anything, the kit was a downgrade. Totally crapped on Vochu's idea.

Kayfun is a very simple and not well made atomizer and its base on Ody design. A poor copy buddy. Dont pay attention to constructions like this

Yep, that happened.

I do like this "upgrade," though. It has some features Vochu's kit doesn't, like the ability to rotate the posts to position your coil(s). It also lacks some features of Vochu's kit, such as compatibility with the Odysseus. And it costs twice as much!

I like 'em both.