The Overlooked Tootle Puffer Gear Thread
- Thread starter roxynoodle
- Start date
- th_trl_thread_readers 0
- Status
Hah! I've had similar happen, but it was quite some time ago. My response was something to the effect of, "I vape at around 15 watts, why are you asking ME?"
These days, I venture as high as 20, or as low as 0.65 on a mechanical. Back when the first Tootle Puffer thread started, I got the impression that 15 watts was the cut-off to be considered a TP, but I gather that's not the case anymore?
Here's the gear I use the most, a DNA30, a DNA40, and a mechanical:
Atties are Cyclones with air holes opened up to a whopping ~1.3mm. I made the mistake of drilling one out to 1/16". Too airy!
Sure, I've got some Chalices and Nuppins too. They go on the nice mods, and are run the same way.
Oh, and y'all can keep your tanks. If I wanna see what's up with a build, all I have to do is pull the cap off and it's right there. No need to drain anything, close valves, or otherwise fiddle around. But I've got 6ml of juice and an 18650 in a form-factor that rides comfortable in my shirt pocket, just like a pack of smokes did for 36 years...
Actually, most tanks you can access your build anytime these days without draining. I only have a few that you can't.
I have a Cyclone and a Nuppin, too.
Well I've run through a tank full with my new Aqua v2.
It is decidedly Meh... Not bad, just Meh.
Back to my Kayfun v4.
It is decidedly Meh... Not bad, just Meh.
Back to my Kayfun v4.
Well I've run through a tank full with my new Aqua v2.
It is decidedly Meh... Not bad, just Meh.
Back to my Kayfun v4.
Really??
Wow, I put this one right behind the Rose for best flavor.
I Vape 1% flavoring so they all taste about the same for me. The throat hit is nice but that is to be expected with a dual coil RTA. The wicking is a PITA compared to the Kayfun v4 and filling the tank... I prefer top fill.
I Vape 66/33 so keeping these flat deck attys from leaking is tricky.
I'm going to mod it for easier wicking and leak resistance tomorrow.
Boden, is that 66 PG or VG? I vape 65 PG/35 VG and mine doesn't leak. I also think this is a great flavor tank, but if you don't use much flavor, I guess that would be wasted on you.
66/33 PG/VGBoden, is that 66 PG or VG? I vape 65 PG/35 VG and mine doesn't leak. I also think this is a great flavor tank, but if you don't use much flavor, I guess that would be wasted on you.
How do you wick it?
I trimmed the tails so they fit just snug in the channels almost reaching the bottom of the channel.
It hasn't leaked yet this way.
Like everything, the wicking will get faster. It took me awhile at first, too, almost a year ago. You should see how fast I do it now. I have 50/50 in both of mine. I've never had a leak.
I will put off modding (for now
)Would you describe your wicking technique.
I just put some Backwoods Brew 555 Exotic 18mg in it. The flavor is quite good.
I will put off modding (for now
Would you describe your wicking technique.
I just put some Backwoods Brew 555 Exotic 18mg in it. The flavor is quite good.
Would pics help? I think I have some on photobucket. I just did one a couple of hours ago.
I found the Aqua SE. The decks are virtually identical.
This is my method on all dual coil tanks that use wick tails. The only thing that changes is the size of the tails. I seperate out the tails. For the Aquas I cut them just above the little rounded part at the bottom of the wick channels. Then I trim the shoulders to fit the curve of the deck.
This is my method on all dual coil tanks that use wick tails. The only thing that changes is the size of the tails. I seperate out the tails. For the Aquas I cut them just above the little rounded part at the bottom of the wick channels. Then I trim the shoulders to fit the curve of the deck.
Got the Prometey! Well for who it was intended - it didnt work out. Vape is too warm for hubs liking..GAWD, I REALLY HATE THAT. Now, guess I'll have to suffer and use it. 
Yes, I'm loving it! Will need more - I believe I have found my utopia. I need to get the fluff right with my DIY - use to vape max VG now more like 50/50 while I experiment with different recipes. Flooded and leaked - stuffed more fluff in now it's vaping bliss! Glad I stalked you Roxy and thank you so much for all you do
Yes, I'm loving it! Will need more - I believe I have found my utopia. I need to get the fluff right with my DIY - use to vape max VG now more like 50/50 while I experiment with different recipes. Flooded and leaked - stuffed more fluff in now it's vaping bliss! Glad I stalked you Roxy and thank you so much for all you do
Maybe this is obvious, but which part of the wick is the shoulder? The part immediately to either side of the coil?
I wicked mine the exact same way I wick my Erls. I use rayon and have it thick at the shoulders, and just a wispy tail going down the juice channels. That sounds pretty similar to what Roxy does, but I may use less in the channels, not sure.
Yes. I puff my shoulders - dont know if it helps with wicking but makes me feel better
Good answer.
- Status
Similar threads
