Have you tried blowing on the atty and play with the top part that seals (screw) the reservoir? (i dont have an L2 
)
)The Precious PV's
- Thread starter caesar
- Start date
- th_trl_thread_readers 0
- Status
Yeah, I tried a quarter of a turn back-off on the top. Just now did a blow but I recently dripped 10 drops in the reservoir (the JD is full) when the 10 drops are gone I'll know and if no luck try a blow again.
Keith-
I recall Caesar mentioning something beyond short circuit protection somewhere along the line.
If I ever do get mine, I'll put it on a bench with 1.5 ohms and let you know what it's doing... I think that amount of power would have probably fried even a cisco atty though if it went on for more than an instant.... or you just got lucky ;-)
Glad to hear you're enjoying it though...
I recall Caesar mentioning something beyond short circuit protection somewhere along the line.
If I ever do get mine, I'll put it on a bench with 1.5 ohms and let you know what it's doing... I think that amount of power would have probably fried even a cisco atty though if it went on for more than an instant.... or you just got lucky ;-)
Glad to hear you're enjoying it though...
JD is working now. I took the cap off and looked to see where I was and that made a difference. Also been blowing but since I took the top cap off and looked it started working. I'm gonna OD on nic... may have to lower nic in my mix.
Datacreek, I have the opposite problem. My JD just keeps on dispensing and except for pouring it out there is no way, I can find, to stop it.
I thought I might have to lower my VG% before it arrived. Thick juice just runs right through it. Don't even have time to get the JD to the PV before I have juice on my hands coming from the bottom.
Attys can be straws. Found that out too... Like straws that warm the liquid flowing being sucked through them.
I thought I might have to lower my VG% before it arrived. Thick juice just runs right through it. Don't even have time to get the JD to the PV before I have juice on my hands coming from the bottom.
Attys can be straws. Found that out too... Like straws that warm the liquid flowing being sucked through them.
What i have found best is to screw on the atty. Add a few drops to the well.Screw on the tank. Then fill the tank. Making sure every thing is tight. I haven't flooded one since.
Thanks for the review Scott!
I'm really upset that Scott got a QC issue. If it was closer to the one I received, this review would have gone in a different direction (not that 8.5 out of 10 is a low score for this price point). The bottom of the head unit on mine is actually worse than shown but the LED hole and atty centering are spec. The inside of the device is irrelevant IMHO. It's not visible.
I rinse out the tank, cap and head unit when it gets put down for a rest (not often). That's a nice feature. I don't think I could live with an atty at an angle that causes issues with the cap/tank though.
I'm really upset that Scott got a QC issue. If it was closer to the one I received, this review would have gone in a different direction (not that 8.5 out of 10 is a low score for this price point). The bottom of the head unit on mine is actually worse than shown but the LED hole and atty centering are spec. The inside of the device is irrelevant IMHO. It's not visible.
I rinse out the tank, cap and head unit when it gets put down for a rest (not often). That's a nice feature. I don't think I could live with an atty at an angle that causes issues with the cap/tank though.
Any more invoices recieved? The last one I know of is 119. I am 138 and impatiently waiting for my precious
Yes very fair review IMO. Thanks for doing it Scott! The atty connection on mine is just fine, as is the hole for the LED. My atty is just slightly off center, but nothing like yours.
On travel for the week and left my Precious Lv2 @ home and missing it... Especially the JD.
On travel for the week and left my Precious Lv2 @ home and missing it... Especially the JD.
Excellent review Scott, well made, fair, thorough, informative as well as very enjoyable!!! 
You now have 1 more YouTube subscriber!!!
Aloha, Keith
You now have 1 more YouTube subscriber!!!
Aloha, Keith
Well, I finally get the replacement part last week for my precious LV2. Unfortunately it came the day I was leaving for vape fest in Philly and I did not have the body with me. So when I got home I put on the new piece and she works like a charm! The feeder takes a little playing with but I was cranking on it last night and it was all systems go!
Been pretty quiet here lately. Anybody have any idea where we are on the preorder list.
Probably best to ask on the site. I do not believe Mark posts here, although he does read!
I was going to post there but i noticed someone else had already asked without an answer, guess it wouldnt hurt to ask again though, thanks for the suggestion.
I got to use a LV2 at the philly vapefest and now its even harder to wait. hopefully i get an invoice soon
Oh that was you, thanks for letting me try yours out, although now Its even harder to wait
- Status
Similar threads
- Locked
- Locked
