The Precise Strata Dual Coil Rebuildable Atomizer/Integrated Tank PV
- Thread starter forcedfuel50
- Start date
- th_trl_thread_readers 0
- Status
This bee is soooo ready.yeahh..but: when flowers blossom, bees will come, no need to call them
Bump for the Strata bees. I'm so ready for this plus the thought of a SuperT rebuildable for my 18350 +P is.........well, I'm anxious to hear what may be.
I forget when this is loosely going to be released. This summer at some point ?
No ETA from David yet. http://www.e-cigarette-forum.com/fo...tomizer-integrated-tank-pv-9.html#post6317280
So, I've been reading the description again and I noticed a mention of dual tanks. Perhaps it's been answered but...does this mean two flavors could be used and still not mix the juices? That would be incredible!
Also, I can't wait to find out more about the proprietary wick that never needs replacing. It sounds incredible. Almost too good to be true. But if there is one vendor I trust emphatically it's David.
I am prepared to sell all my mods and rebuildable attys for this. The controllable air flow will make a huge difference. Plus, I'm pretty rough on my mods. I always carry in my pocket and having this be all threaded means it's totally up to the challenge. I'm too excited and have decided I will own this mod. I can't imagine missing this innovation. It has the potential to one up and improve upon so many aspects all in one device.
One last question. Would a replacement cap turn the base into a standard precise? I'm pretty sure I read it would but just wanted some confirmation.
Until then...I'll be drooling over these CAD pics.
Also, I can't wait to find out more about the proprietary wick that never needs replacing. It sounds incredible. Almost too good to be true. But if there is one vendor I trust emphatically it's David.
I am prepared to sell all my mods and rebuildable attys for this. The controllable air flow will make a huge difference. Plus, I'm pretty rough on my mods. I always carry in my pocket and having this be all threaded means it's totally up to the challenge. I'm too excited and have decided I will own this mod. I can't imagine missing this innovation. It has the potential to one up and improve upon so many aspects all in one device.
One last question. Would a replacement cap turn the base into a standard precise? I'm pretty sure I read it would but just wanted some confirmation.
Until then...I'll be drooling over these CAD pics.
Good evening ECB,
It is a single tank with dual feeds since its dual coil, each has a feed but they both feed from a common tank. Sure thing on the cap replacement
Thank you. I was trying to imagine a "feed" and thinking more along the vapemate route. It made my brain hurt just a bit. This makes more sense and should maintain a small footprint while holding the most juice.
I think the 4ml size should be perfect.
Still curious about the wick but I'll remain patient and await more details.
I never owned a vapemate but I'm excited to see the viewing glass up close and in person on this unit.
You continue to create and innovate David. Thank you.
I think the 4ml size should be perfect.
Still curious about the wick but I'll remain patient and await more details.
I never owned a vapemate but I'm excited to see the viewing glass up close and in person on this unit.
You continue to create and innovate David. Thank you.
Why dual coils? I understand the reasoning behind airflow control and integrated tank but why incorporate dual coils in this design. Will these be wired in parallel so that if one pops you still have one functioning coil? If you are looking for 2.0 ohm type heat will both coils need to be made so that they meter at 2.0 ohms? What if one coil is 2.0 ohm and the other is 3.0 ohm running on a single IMR 3.7 volt AW? It will be interesting to see how these coils are implemented but I am guessing they will be vertical due to the limited real estate of the 18mm footprint.
Anticipation ....
Sent from my iPhone using Tapatalk
Anticipation ....
Sent from my iPhone using Tapatalk
First, you can run it as a single coil if you prefer. They are independent coils, not a single coil wrapped into "two coils" so if one burns out, the other still functions. I made it dual coils for flexibility and options in vaping styles. Dual coils have the primary function of more vapor, though that too can be manipulated by the resistance of the coils you wrap as well as airflow adjustment.
Last edited:
The more I hear the more I can't stop thinking about it. Truly innovative and versatile design.
I'm curious as to the permanent atty. I would love to not build. That's exciting. Thanks!!!
The atomizer heating coils themselves will need periodic replacement and are of the standard Kanthal or Nichrome.
I'm hoping these will be easily replaced and use some kind of locking nut instead of wrapping the kanthan around wire leads.
- Status
Similar threads
- Locked
