The Reonauts new lounge

[Gigdujour]

i need shelves!

T

I've got shelves, a toolbox and a hutch...yet there are still around a half dozen or so mods on my little table next to my chair. For some reason, this drives The Evil One nuts [emoji848]


Master of Bassets...and not much else

 

[supertrunker]

I've got shelves, a toolbox and a hutch...yet there are still around a half dozen or so mods on my little table next to my chair. For some reason, this drives The Evil One nuts [emoji848]


Master of Bassets...and not much else

i thought you owned half of Michigan!

T

 

[Gigdujour]

i thought you owned half of Michigan!

T

I only own the swampy part. I'll have to petition The Evil One for a vape barn [emoji6]


Master of Bassets...and not much else

 

[supertrunker]

A barn indeed! Some mere mortals settle for a small corner of a house! i have one small corner and the rest is largely out of bounds.

I've not been officially banned from the kitchen here yet, but that's because i haven't fixed the light over the sink!

T

 

[classwife]

This is my vaping hutch (before I got it home)

Older Folks and Vaping Back Porch - Part Five

 

[Train2]

Did a little topper-swapping, after my O-16 got in.
It's right at the "minimum" air for me - but it's sure a great vape in a tiny package. I kept not-buying one, but then they started to disappear, so I grabbed one...

 

[supertrunker]

What coil, wicking and all that old guff? Does it rival an RM2?

T

 

[Train2]

Surprisingly, despite a pretty substantial collection of tight little atties - I never ran an RM2!
I've vaped Cyclones, Reactors, Atomics, Divos...then when I wanted more air moved to Nuppins, Rogue, Manta...

My GUESS is that you could dial it down as tight as you wanted. Full open, it is a TINY LITTLE bit tighter than a Nuppin wide open.

I have a go-to build in it dual 27 g kanthal, 2.5mm, 6 wrap for just a touch under 0.5 ohms.

What coil, wicking and all that old guff? Does it rival an RM2?

T

Edit - I picked up and have been wicking everything with "Vapers Choice" cotton. The stuff in a little jar? I find it's not too different in taste from my other fave japanese cotton, but seems to LAST longer. It takes a few minutes to get wet initially, but then seems to resist gunking or scorching a bit better.

 

[supertrunker]

i use readywick abbreviated to RxW usually and it's indestructible, but i do have one fused Clapton with rayon in it and it's done very well.

Naturally i cannot help but quote you.

It takes a few minutes to get wet initially

but seems to LAST longer.

T

 

[Sterno]

i prefer a cotton called Texas tuff

 

[PapawBrett]

Good Morning Reonauts. Another Monday is upon us.

Have a Safe and Blessed Day

 

[supertrunker]

This is my vaping hutch (before I got it home)

Older Folks and Vaping Back Porch - Part Five

i did see that before but i had to make sure HRH could not see the screen else she'd want one!

i bought some cheap steel shelving for her utility room so she can store cans and whatever in there but i really need some shelves for my room. i know wood can be expensive having bought a few wooden mods, but bloody hell!

T

 

[donnah]

I'm wanting to drill out some bottle caps.. the original 6ml caps. I've not seen this talked about before.. is there a preferred way to do it?

 

[puffon]

I'm wanting to drill out some bottle caps.. the original 6ml caps. I've not seen this talked about before.. is there a preferred way to do it?

Drill bit size is 11/64"
Preferred way would be to use a drill press, but not necessary.
I like "brad point" bits, as it cuts a cleaner hole, but not necessary.
Basically you need a 11/64" hole, centered in the cap....

 

[classwife]

i did see that before but i had to make sure HRH could not see the screen else she'd want one!

i bought some cheap steel shelving for her utility room so she can store cans and whatever in there but i really need some shelves for my room. i know wood can be expensive having bought a few wooden mods, but bloody hell!

T

Yard sales, thrift shops, Craig's List...all great places to find storage shelving/cabinet/stuff !

 

[supertrunker]

The idea is to get away from using o-rings at all in the bottle and this becomes especially important if you vape battery acid as i do, when the o-rings will rot and fail in 3 months or so.

What you are looking to end up with is the tube resistant to being pulled out, but that it expands against the plastic.
I'm sure there was a thread by Masterofnone called the bottle mod in the old Reo forum.

T

 

[oplholik]

This link may help. Post# 9. You can read up and down from there.

REO bottle fix?

 

[donnah]

Thanks guys.. I've got lots of caps that I need to mod. Another question.. tubing.. is the dimensions still 1/16" ID x 1/8" OD x 1/32? Looking at the tubing I have now it reads 1/16 x 3/16.. if the size has changed I don't want to order 10ft (minimum order) of the wrong size!

 

[supertrunker]

Tubing is measured by the inner diameter and the outer diameter. If you subtract one from the other and divide it in two - because it's a tube and has 2 sides, then that gives you the wall thickness.

In your example above 1/32" will be how thick your liquid tube is.
Here.
Accessories

T

 

[Debadoo]

i did see that before but i had to make sure HRH could not see the screen else she'd want one!

i bought some cheap steel shelving for her utility room so she can store cans and whatever in there but i really need some shelves for my room. i know wood can be expensive having bought a few wooden mods, but bloody hell!

T

If you're crafty you can make this.......the rack is 17.00 at Walmart
How To - Home & Family: DIY Laundry Rack Shelf | Hallmark Channel

Thanks guys.. I've got lots of caps that I need to mod. Another question.. tubing.. is the dimensions still 1/16" ID x 1/8" OD x 1/32? Looking at the tubing I have now it reads 1/16 x 3/16.. if the size has changed I don't want to order 10ft (minimum order) of the wrong size!

are you getting it at ebay or somewhere else?