Got one of those to work on my fishing gear - my problem is short fat stiff fingers.
Tootle Puffers, Part Three! (The Sequel of the Redux)
- Thread starter Katdarling
- Start date
- th_trl_thread_readers 0
Got one of those to work on my fishing gear - my problem is short fat stiff fingers.
Well that was fun. Opened it up. Cleaned it, selected the 1.5ohm coil, primed it, filled tank. I knew the airflow was wide open so I used one of my atomizer rings to limits it and then attempted to vape. This is not a MTL tank unless you do some serious blocking of the airflow both in the tank and on the coil head.
After a few mins the tank has travelled across the table to Hubby's Side (DTL just a tad sub ohm)
Quite an ingenious little designIn the spirit of thread title.
Stealth Tootle...
Boost Labs Izi Clone on an 18350 Colibri, 1.2 ohm 2.5mm 28g variable air flow from 1x .8mm to 4x 1.5mm, tight MTL,- tight DTL. Tiny chamber provides excellent flavor. PEEK, Ultem, and 316SS.
The chamber.
Well that was fun. Opened it up. Cleaned it, selected the 1.5ohm coil, primed it, filled tank. I knew the airflow was wide open so I used one of my atomizer rings to limits it and then attempted to vape. This is not a MTL tank unless you do some serious blocking of the airflow both in the tank and on the coil head.
After a few mins the tank has travelled across the table to Hubby's Side (DTL just a tad sub ohm)
I should mention that the driptip was a source of irritation with the reviewers. Very wide bore, some normal driptips fit but look odd perched about the tank. The byleo external lips driptips are perfect for this. They are meant to go over the outside of cartomizers and they operate the same with these coils
Orange! Orange! Ohmagosh it comes in orange.I'm a confirmed MTL Tootle Puffer (usually end up 10W-11W)...with NO interest in rebuilding...
But then I ran across this thread eGo ONE tank series – CLR coil and decided to try an "eGo ONE Mega V2 Tank" and a 5-pack of CLR Coils-1.0Ω.
The eGo ONE Mega V2 Tank is 4ml., has AFC (can dial down to a quite enjoyable MTL level) and, although it's Bottom-Fill, is pretty quick/easy to refill.
The CLR coils are manufactured to be rebuildable...(and come with a set of instructions in each 5-pack).
However, since they're about the same price ($9-$10 for a 5-pack) as other coils, I'm planning on using them just like my other blister pack coils.
(They have very good "flavor" and a somewhat "dense" vapor.)
But...I figure when I'm finished with a coil I'll just toss it into a baggie...
Then...depending on how bad this FDA Dooming stuff gets...I'll try replacing the wick.
(And, if things get really bad...I'll try replacing the coil itself...)
Joyetech eGo ONE Mega V2 Tank
Joyetech CLR Coils (5 pack)
..
OH YEA - I'll NEED one too . . .
alright thanks for the info I think ill pass on this oneIt is alright, not a favorite, fit & finish is pretty nice. Up to 6x 1.8mm air flow holes in the base, but a bit foolish since the air under the coil chokes it down quite a bit. I opened up the air flow under the coil, ended up being much better, still restrict it down to a tight MTL, but now wide open I can do restricted lung (my preference).
Filling is a bit of a PITA, you'll need a syringe or one of those near zero flow needle tip bottles. You can bottom fill Taifun style, but have to be really careful or you'll end up with a mess. Deck is quite tiny, wicking can be a little tricky, need to get everything pretty much spot on or its going to flood/gurgle. not all drip tips fit in it, it is a bit on the small side for some.
Flavor is nice, overall performance is pretty decent, but because of annoying fill method I don't use it much. I've tried a few authentic parts on it, and everything has fit.
Once it is full, and wicked properly it really is a quite nice vape, however I have other tanks that perform at this level and are much more user friendly.
Nice.......I was going to get one when it was cloned looks pretty good.In the spirit of thread title.
Stealth Tootle...
Boost Labs Izi Clone on an 18350 Colibri, 1.2 ohm 2.5mm 28g variable air flow from 1x .8mm to 4x 1.5mm, tight MTL,- tight DTL. Tiny chamber provides excellent flavor. PEEK, Ultem, and 316SS.
The chamber.
Does that mean you liked it?
(Thanks! Seems like a pretty objective review!!)
Its kind of one of those things, don't regret the purchase, I'll pull it out time and again, but it will never make to the commonly used rack, and will mostly gather dust.
Orange! Orange! Ohmagosh it comes in orange.
Whew, I was afraid this was another Pink, Pink, Pink thread...
Yea - I may have 31 Nieces/Nephews - Great Nieces/Nephews - Great-Great Nieces/Nephews and still counting, however they all live up North or out West and have lives that do not include coming to Florida to help "Me" . . .
HaHa LOL... Mine are in Florida - about 350miles away, but it will be a good excuse to visit and while now some of them are only 10 or 11 yrs old - they will be a teen looking for cash by the time I need coils rebuilt...
Hey Uncle, Long time no see. Hope your doing good...
Whew, I was afraid this was another Pink, Pink, Pink thread...
Can totally ignore pink but the mere hint of Purple
And I am all ears
Let us know how you like the eVic mini. I'm curious (and looking
I do like it JK !
It's the smallest mod I own and fits well in my pocket for out and about.It even comes with a silicone sleeve for some protection.It's fairly durable as I've dropped it twice so far on a hard linoleum floor from ~3 feet up with a kayfun lite atop of it and it still works.
It has temp control if I ever get around to trying that and a fancy schmancy clock to boot.
My only niggle with the mini is the magnets in the battery door.When I pull the mini out from my pants pocket all my dimes and quarters tend to come out with it too.
It's a fine little machine and works well!
It comes in orange too...
http://www.canvape.com/ProductDetails.asp?ProductCode=EvicVTwoMiniExpress
Similar threads
- Locked
