Turbo Cartomizers for AFS!

[JBTX1]

Rob...This may have already been discussed in another thread but I am unable find it if so. My questions is, do you have any plans on carrying the the Turbo Cartomizer that is being used on the AFS V2?????? The ones that folks are modifying to work by drilling a hole in. I know they measure 3.7 ohms on the volt meter.

 

[SSRob]

We're workin on it

Rob

 

[SR219]

We're workin on it

Rob

Are you working on getting them already drilled?

 

[mwa102464]

I would like to see these in HV & LR ready for the AFS that would really be sweet Rob.!!

 

[SSRob]

HV possible. LR never. I see too much of a chance of the filler burning up with a LR configuration.

 

[JBTX1]

HV possible. LR never. I see too much of a chance of the filler burning up with a LR configuration.

I totally agree Rob!

 

[SR219]

Heyyyyyyyyyyyy, answer my question

 

[SSRob]

Woooooops! Sorry.

I will check with the factory about drilling them...shouldn't be a issue. Does anyone have the ideal location for the hole? Size?

 

[Grammie]

That would be emonty I believe (about where to drill the hole).

 

[JBTX1]

Rob...Im sure you can get a ton of measurements in mm and personal preferences. That being said I will suggest what I have been drilling them at. From the bottom of the threaded end to centerline of the hole is 1/4" inch. The hole size is 5/64" inch diameter. These dimensions will completely drain the liquid from the AFS. It's not a precise science on these things. Good lord I hate the metric system...lol....but then im old school and like to keep it simple and I know the chinese use the metric system. Conversion table will get you close to the needed measurements. I have drilled out probably 50 of them and they are working flawlessly with those dimensions. One other suggestion....No stickers please, just bare metal tubing. No soft rubber caps or any hard caps are needed either. The adhesive/sticker and caps are just another cost that is not needed. That alone should offset the cost of the hole. They are set up to make holes for 901 attys anyway. They should be cheap and easy for them to manufacture.

 

[SSRob]

I've sent specs to the factory rep and am waiting on a response. I already requested that they make them without stickers.

We'll see what they come up with.

Thanks
Rob

 

[JBTX1]

Muy Bueno Senior Roberto!

 

[SSRob]

De nada.

Donde esta la cerveza?

 

[JBTX1]

Bebi' todo!

We sure need an OKIE/TEXICAN vapefest brother!

 

[clyde2801]

Hmm....Lake Texoma would be good, no?

 

[SSRob]

Hellz yeah I wouldn't mind some Striper fishin!

 

[JBTX1]

Striper Fishing! Now were talking!.....fishing is my middle name! I'm up for it! clyde...once again my friend, you always do justice the every thread you post on! Excellent idea!....Lets do this! I'll buy the cerveza!

 

[clyde2801]

Striper Fishing! Now were talking!.....fishing is my middle name! I'm up for it! clyde...once again my friend, you always do justice the every thread you post on! Excellent idea!....Lets do this! I'll buy the cerveza!

Rarely have we seen a person fail who has throughly followed our path...I mean, I'll pass on the beer, thanks.

 

[JBTX1]

Rarely have we seen a person fail who has throughly followed our path...I mean, I'll pass on the beer, thanks.

I totally understand clyde....I remember the thread now. I'll buy you all the iced tea and soda pops you can drink my friend!...JBTX1

 

[clyde2801]

I totally understand clyde....I remember the thread now. I'll buy you all the iced tea and soda pops you can drink my friend!...JBTX1

Now you're talking! And we can all bring our dremels!

BTW, got some havana gold from porphy at ave juice, who btw is closer to you than Rob in Lawton, and filled up a 3/4 full afs and oooh mah gawd!

Even when mixed with dekang marl mix a dedicated cigar smoker friend who never vaped before thought it tasted like a cigar....or a really good pipe tobacco! Even has a cigar after taste.