The costs of running this huge site are paid for by ads. Please consider registering and becoming a Supporting Member for an ad-free experience. Thanks, ECF team.

WARNING!!! PrecisePlus owners MUST read...

Discussion in 'Super T Manufacturing' started by forcedfuel50, Nov 10, 2011.

Image has been removed.
URL has been removed.
Email address has been removed.
Media has been removed.
  1. forcedfuel50

    forcedfuel50 Unregistered Supplier ECF Veteran

    Just a reminder:

    Do NOT clean your Precious Metal Rhodium plated contacts with sandpaper, cream polishes, abrasive pads, chemical cleaners, deoxits, brasso, mothers, flitz, cape cod cloths etc etc etc!!! I can't drive this home enough. Both the bottom switch screw in post, switch on the 10440 and top cap center post are Rhodium plated.

    Rhodium is a precious metal, just like gold, it won't tarnish, rust, deteriorate, corrode or oxidize. You can bury it in the ground and dig it up 10,000 years from now and it'll look just like it does today.

    The ONLY thing you should be cleaning it with is a soft cloth. If it get dustys or some juice on it, just wipe it off with a soft cotton cloth. Worse case scenario, you drop it in the mud, you can wash it with some warm water and soap and then wipe it dry with a soft cloth.
  2. atavanhalen

    atavanhalen Ultra Member Verified Member ECF Veteran

    Keep this on top, I assume by you posting this that some unlucky soul did not read the paperwork that came with the preciseplus.
  3. artyoh

    artyoh Senior Member ECF Veteran

    Aug 22, 2011
    Shenandoah Valley
    Maybe a day-glow orange warning sheet or sticker in the box or on the mod in a large font with lots of !!!!!
  4. D133

    D133 Senior Member ECF Veteran

    Oct 25, 2009
    I'm very happy with my 18350. 510 atomisers do leak if I over-drip, but no juice has ever entered the battery tube (unlike other mods I have used).
    My question is, is the top-cap centre post rhodium plated on both ends? (post at atomiser end).
    This is the only part on the Super-T I have ever had to wipe, and I now use a cotton cloth, but would kitchen roll be deemed abrasive (as it is better for wiping up liquid)? Thanks.
  5. atavanhalen

    atavanhalen Ultra Member Verified Member ECF Veteran

    Yes the entire post is plated, I assume when you say kitchen roll you mean paper towel, I have been using paper towel to wipe juice off of it and have not had any problems but maybe David can chime in to confirm that, I am sure a microfiber towel from the dollar store would be best but like you said paper towel soaks juice up nicely, toilet paper or tissue would be a softer choice.
  6. D133

    D133 Senior Member ECF Veteran

    Oct 25, 2009
    Hi, thanks for your reply. Yes, I meant paper towel, but as you say there are even softer options.
  7. bmwjen

    bmwjen Reviewer / Blogger Verified Member ECF Veteran

    Feb 2, 2011
    I don't even clean the contacts on any of my mods. um, am I suppose to?
  8. Hrathor

    Hrathor Super Member Verified Member ECF Veteran

    Oct 27, 2011
    Canton, MI
    Only if you aren't getting good contact. A strong battery and good atty/carto will still seem weak if your contacts are dirty/corroded. I usually use an eraser or some Ever Clear (NOT on Rhodium though). If one of your mods isn't performing well and everything else checks out look at your springs and contacts.
  9. nomer

    nomer Full Member

    Dec 6, 2011
    thanks for this info! :)

    im very happy with the performance of my P+18650 :)
  10. erictho

    erictho Super Member ECF Veteran

    Oct 2, 2011
    this op makes the archaeologist in me happy. :)
  11. Koman

    Koman Moved On ECF Veteran

    Jan 7, 2010
    I don't clean them, too. I don't think you have to.
  12. proggieus

    proggieus Senior Member Verified Member ECF Veteran

    Jun 12, 2011
    many many mods (most?) will work better if you clean the contacts and electrical connections, Even the on the Precis i notice a difference after cleaning the threads and the sides of the button with just a damp cloth or paper towel. Dirt, finger oils, and oxidation can effect the electrical flow between surfaces.
  13. LadyMaMa

    LadyMaMa Super Member ECF Veteran

    Sep 16, 2009
    SE Minnesota
    Reminder Bump:)

  14. tnt56

    tnt56 Vaping Master Verified Member ECF Veteran

    So is ISO allowed with a Q-Tip?
  15. Riverboat

    Riverboat Vaping Master Verified Member ECF Veteran

    Feb 15, 2012

Share This Page